Electronics Forum: expired and smt and components (Page 1 of 13)

tape and reel components

Electronics Forum | Fri Sep 13 15:39:54 EDT 2002 | DANIEL

Are there very many companies that send there smt components out to be put on tape and reel

Bottom side smt and thru hole

Electronics Forum | Tue May 26 22:13:15 EDT 1998 | Pat Copeland

R&D is currently designing a board with smt components on both sides of the board. They are adding a 16 pin IC Gull wing. on the bottom side of the board. I have asked for only caps and resistors to be placed on the bottom side. Is there a recommende

Re: Bottom side smt and thru hole

Electronics Forum | Sun Jun 07 09:43:11 EDT 1998 | Bob Willis

There are some guidlines on design and through hole reflow on my web site to download. Also on pin in hole reflow the SMTA Office has a document on using the tecnology. | R&D is currently designing a board with smt components on both sides of the bo

smt common pad 0402 and 1206 package

Electronics Forum | Fri May 06 08:47:05 EDT 2016 | davef

You're correct. This design will have a record amount of 0402 rework for tombstoning and misalignments. Suggest that the pads on each end of all components be the same size in order to balance wetting forces during reflow.

Re: Bottom side smt and thru hole

Electronics Forum | Wed May 27 13:42:08 EDT 1998 | Chrys

| R&D is currently designing a board with smt components on both sides of the board. They are adding a 16 pin IC Gull wing. on the bottom side of the board. I have asked for only caps and resistors to be placed on the bottom side. Is there a recommen

Re: Bottom side smt and thru hole

Electronics Forum | Wed May 27 14:35:52 EDT 1998 | Justin Medernach

| | R&D is currently designing a board with smt components on both sides of the board. They are adding a 16 pin IC Gull wing. on the bottom side of the board. I have asked for only caps and resistors to be placed on the bottom side. Is there a recomm

Re: Bottom side smt and thru hole

Electronics Forum | Wed May 27 10:19:43 EDT 1998 | Jerry

We have no problems but orientation does matter. Orient with longest side of component body perpendicuar to wave. In other words the same preference as with through hole DIPS. Idea is the same as for through hole, that the surface tension will ten

Laying down and holding large components

Electronics Forum | Thu May 22 14:16:40 EDT 2003 | MikeF

We need more information to give you a good answer. Is this a leaded part (axial or radial) or smt? How big is the part, how much weight per lead? What is the end use environment, will it see any vibration? or temperature extremes? Some general com

Solder Paste and fine pitch components

Electronics Forum | Wed Sep 18 10:06:30 EDT 2002 | Bob M

I place 15-20 mil a lot. You need to look at your pad to apature reduction. Your stencil thickness. The type of paste your using. We use 2-5 mil reduction on each side as a general rule on fine pitch. This varies depending on pad width. We also use 5

Solder Paste and fine pitch components

Electronics Forum | Thu Sep 19 11:14:45 EDT 2002 | Jim M.

We had lots of problems with bridging on 15.8mm pitch, QFP17-160 at the start.The board was .032 thick, double sided-six boards to a panel. Here is the problems (not neccessarily in the biggest to little but as i remember them) and solutions that he

  1 2 3 4 5 6 7 8 9 10 Next

expired and smt and components searches for Companies, Equipment, Machines, Suppliers & Information

KingFei SMT Tech
KingFei SMT Tech

Main Products: 1. Original new and Original Used SMT/AI Spare Parts. 2. SMT Equipments And Related Machine( SMT Calibration, SMT Feeder Carts,Conveyer etc.) 3. Maintenace and Repair Service Pre-Sales Service Provide details ab

Manufacturer's Representative / Manufacturer / Equipment Dealer / Broker / Auctions / Consultant / Service Provider

Building A, Jiepeng Square, Fuyong
Shenzhen, 30 China

Phone: 0755-33578694