Electronics Forum: fiducial and table (Page 1 of 11)

fiducial

Electronics Forum | Thu May 13 10:43:34 EDT 2004 | rob_thomas

hi, i have a question relating to fiducial, is > the fiducial normally comes with the pick and > place data from the custommer or we have to > define it by ourself? how to set its coordinate > so that the cp6 and ip3 (using Fujicam software) > w

fiducial mark

Electronics Forum | Tue Mar 02 22:40:52 EST 2004 | pdeuel

To clean up other replys I will add that some most all machines have global correction. Most placements are an off sets from pcb 0,0 usually the lower left corner of the board. When the machine locates the fiduitals and these fids are not exactly whe

Block repeat and fiducial relation

Electronics Forum | Tue Aug 19 14:16:51 EDT 2008 | jax

It depends on whether the Fiducials are Circuit Fiducials (located on the PCB) or Block Fiducials (located on the Panel) His way would be for Block Fiducials.

Block repeat and fiducial relation

Electronics Forum | Tue Aug 19 13:35:51 EDT 2008 | stefi

Hello, I need an advice regarding the next issue: in the case of Assembleon Topaz or Emerald SMT machines, is there necessary to teach first the block repeat coordinates and after that the PCB fiducial coordinates when you do not have these coordina

Block repeat and fiducial relation

Electronics Forum | Fri Aug 22 15:26:18 EDT 2008 | rway

I rarely use blk fiducials. But when I do, they are always programmed after the fids. It's the fids that sets your general alignment of the panel. I only use blk fidus for thin pcbs (30 mil) that tend to warp when on the conveyor.

Block repeat and fiducial relation

Electronics Forum | Thu Aug 21 19:18:47 EDT 2008 | duchoang

My steps are different in that case: 1- Check mounts. Try to adjust origin point until get the pretty good mount positions. 2- Teach fiducials ( Board fids, not panel fids) 3- Use fids, check mount again. 4- If OK, then teach Block Repeat. This alwas

Block repeat and fiducial relation

Electronics Forum | Fri Aug 22 15:27:13 EDT 2008 | wayne123

this is the order that I use. 1. Teach pcb origin 2. Teach fiducial location 3. dial in vision on fid in mark info. 4. go into mount and verify that the primary image is on in x/y (after perfoming a teach trace condition) and then do any offsetts if

contact pick and place table not homing

Electronics Forum | Fri Aug 11 13:38:52 EDT 2023 | lauri

We have a Contact 3AV pick and place and we can't get the table to home. Any solutions?

contact pick and place table not homing

Electronics Forum | Thu Nov 02 22:29:47 EDT 2023 | murtaza

Burn that machine. I had 3 of them and i was fixing it more than running boards

contact pick and place table not homing

Electronics Forum | Thu Aug 17 13:55:45 EDT 2023 | markhoch

I think we need more information. Is it moving at all? Does it move to a reference position and then stop before returning to the home position? Have you verified that all sensors are working correctly? Does the machine use stepper motors, motors & e

  1 2 3 4 5 6 7 8 9 10 Next

fiducial and table searches for Companies, Equipment, Machines, Suppliers & Information

December 2024 Auction

High Precision Fluid Dispensers
pressure curing ovens

Software for SMT placement & AOI - Free Download.
High Throughput Reflow Oven

Smt Feeder repair service centers in Europe, North, South America
Win Source Online Electronic parts

We offer SMT Nozzles, feeders and spare parts globally. Find out more
SMT feeders

Training online, at your facility, or at one of our worldwide training centers"