Electronics Forum: foam fluxer specific gravity (Page 1 of 5)

Re: Spray fluxer vs.Foam fluxer

Electronics Forum | Wed Nov 11 00:42:15 EST 1998 | Jason

Mike, We retrofitted all of our waves with USI spray fluxers. We are running no-clean on 4 of our waves, and OA 2331-ZX, reduced specific gravity to .825, on the other 2 With OA you must buy a special spray head to accomadate higher pressure and l

Re: Spray fluxer vs.Foam fluxer

Electronics Forum | Tue Nov 10 09:27:04 EST 1998 | Chrys

| | | I need to find out the benefits about having a spray fluxer.Right now we are using a foam fluxer on our electrovert wavesolder. We are thinking about investing in a spray fluxer and I want to know if anyone has used a spray fluxer and if any pr

Foam fluxer maintenance, storage and cleaning

Electronics Forum | Sun Nov 08 15:27:25 EST 2015 | davef

Thinner: Flux thinner, NOT paint thinner We kept a spare stone in thinner in inventory. We cut PVC pipe to size, cap in one end, screw thread on the other, stone inside, filled with flux thinner and covered with a screw cap. I don't remember who we

Foam fluxer maintenance, storage and cleaning

Electronics Forum | Mon Nov 09 09:44:22 EST 2015 | davef

Purpose. This describes setting-up a wave soldering system set-up for a new assembly design or checking a wave solder machine operation with a test board. Applicability. To be used for new design printed circuit assembles and during machine accept

Re: Wave Solder Flux Out With The Old & In With The New

Electronics Forum | Mon Jul 20 20:58:54 EDT 1998 | Dave F

| | Dave: | Wayne is correct with his analysis of ultrasonic spraying - we also use Sonoteks. However, your post didn't ask for a different system, just a clarification regarding your problem. What type of flux system are you currently using - s

Re: Wave Solder Flux Out With The Old & In With The New

Electronics Forum | Mon Jul 20 20:58:49 EDT 1998 | Dave F

| | Dave: | Wayne is correct with his analysis of ultrasonic spraying - we also use Sonoteks. However, your post didn't ask for a different system, just a clarification regarding your problem. What type of flux system are you currently using - s

Re: Wave Solder Flux Out With The Old & In With The New

Electronics Forum | Tue Jul 14 15:02:38 EDT 1998 | Brian Conner

Dave: Wayne is correct with his analysis of ultrasonic spraying - we also use Sonoteks. However, your post didn't ask for a different system, just a clarification regarding your problem. What type of flux system are you currently using - spray, f

Foam Fluxer problems

Electronics Forum | Mon Dec 18 11:04:43 EST 2006 | Steve

Are you making sure that the all the alcohol in the stone is pretty much gone before you put it in the tank? If the stone is dripping with alcohol when you put it in the tank, you could be affecting the specific gravity of the flux so much that it ca

Foam Fluxer problems

Electronics Forum | Mon Dec 18 12:06:15 EST 2006 | realchunks

Always check your specific gravity. It directly affects your faoming. Put ping pong balls in your fluxer to reduce your thinner from evaporating.

Wave soldering profiling

Electronics Forum | Fri May 07 12:39:01 EDT 2004 | rontdc

Bruce, Using a foam fluxer with no-clean flux is a very touchy situation. It is imperative that the specific gravity of any flux be maintained within the manufacturers recommendations. If it is not, you will get icicles and bridging. Maintaining the

  1 2 3 4 5 Next

foam fluxer specific gravity searches for Companies, Equipment, Machines, Suppliers & Information

ISVI High Resolution Fast Speed Industrial Cameras

High Throughput Reflow Oven
Fluid Dispensing, Staking, TIM, Solder Paste

Training online, at your facility, or at one of our worldwide training centers"
Pillarhouse USA for handload Selective Soldering Needs

High Resolution Fast Speed Industrial Cameras.