Electronics Forum | Mon Aug 15 06:17:47 EDT 2005 | md
All, I have a very annoying problem with the FIP3 machine. A while ago i had an issue with 2 sensors (only!) basically they were not sensong boards etc. when I checked the voltage I had 12 volts on the GB line which should have been 0v. This proble
Electronics Forum | Thu Feb 02 20:48:07 EST 2006 | ____
I would like to start a new post regarding fuji > NXT machine. What do you think about the machine > as far as the servicing of the machine goes. I am > so used to the older machines such as : CP,IP, > and QP. Those machines at least give you som
Electronics Forum | Fri Feb 17 12:53:30 EST 2006 | bvdb
We just got our used Fuji IP-1 working well. Sometimes during testing of a new program/pcb we like to stop the run and re-start with a clean board. When we make the IP-1 eject the unfinished pcb and start with a new pcb the IP-1 does not scan the f
Electronics Forum | Wed Apr 12 11:09:55 EDT 2006 | Cmiller
So, you are going to be putting down about 3 million parts a day? How many shifts are you running? At 24 hours a day and assuming the machines never stopped placing parts (which is not possible) you would need a line that put down 125,000 parts an ho
Electronics Forum | Mon Jul 03 03:15:35 EDT 2006 | bvdb
Thanks in part to help from the good people in this forum we've got our 1989 Fuji IP-1 working really great! We can run for hours without missing a beat (except to replace empty reels). Although I'm careful to lubricate as per the instructions the
Electronics Forum | Wed Aug 30 03:58:26 EDT 2006 | Ola
Yes you do need a different upline interface card. This information should be in Your Technical Reference Manual, Electronics enclosure chapter 6? Y2 Enclosure, card position X8 Downline and X9 upline: Part No Description. 112045 Base Card
Electronics Forum | Fri Sep 15 15:55:27 EDT 2006 | jdengler
Bert, Hopefully the MCS still has PD's from Fuji or the previous user. The Transverse rate IP set in them should be a good guide for any new PD's you may need to make. This speed is usually set as high as possible and still get accurate placements
Electronics Forum | Thu Dec 07 12:29:57 EST 2006 | fastek
It makes sense if you think about it. Siemens was a dead company ready to fold up their tents back in the 80's and early 90's. To their credit they stuck to their platform...got somewhat lucky and the market sort of came to them as the wave of users
Electronics Forum | Fri Dec 08 14:54:06 EST 2006 | Terry
Siemens is the General Electric of Europe. Like GE, Siemens typically is in the top 3 positions ($ market share and profit) or they exit the business. In total revenue I expect Siemens to be in the top 2-3 globally. In units I expect Yamaha has the
Electronics Forum | Mon Dec 18 21:23:13 EST 2006 | jgarver1
The spline shaft is bent. I have replaced a number of these over the years with the exact same symptoms. How is your placement? Your 180 degree placements should be skewed if the shaft is bent. 0 Degree placements are typically acceptable due to
Focusing on the SMT field for more than 15 years, QYSMT has been committed to meeting the needs of customers and partners. Our mission is to provide the best solutions while helping to reduce costs and increase efficiency.
Manufacturer / Equipment Dealer / Broker / Auctions
2nd floor, West side, Building 12, Hengmingzhu Industrial Park, 32 Xiangxing Road, Shajing Tongfu Industrial Zone, Baoan District
Shenzhen, China
Phone: QYSMT / MOREL USA CONTACT – SUSANTA TRIPATHY.: 1-912-373-4005 / China Contact: 86-075521635007