Electronics Forum | Wed May 27 16:39:33 EDT 2009 | rmitchell
Hi, I think vision 20 will work as well. If not we have used 100 or 105. Have you tried placing the part with the machine trace on? If so is it finding all the leads? any error codes? If you are defining the leads in the EL lead data I would not d
Electronics Forum | Wed May 27 18:19:58 EDT 2009 | dcell_1t
yesterday I tried with vision type 20, just defined the two pair of leads and error 1CA14003 came up, on flexa error help says the following: Cause: The Vision_type in part data is expressed using hexadecimal notation (??). If ?? equals 0A, 0B, 0C,
Electronics Forum | Tue Jan 05 20:21:40 EST 2010 | steinerson
Hi Jeff I would recommend you to try unexpensive user friendly Juki Late Model KE760 series. you need a flexible machine that can handle components,fine pitch QFP. This machine is very unique. you can use even without an offline software optimizer,
Electronics Forum | Sun Apr 25 21:01:57 EDT 2010 | m79d
Hi all our IP1(1993)is not reading the board fiducials, the light comes on at the fid camera and stay on and the machine just hangs. Need to press the emergency stop button to go any further and screen says 'mark not readable'. None of the bulbs h
Electronics Forum | Tue Apr 27 16:42:18 EDT 2010 | m79d
Hi jepoy + a very frazzled man thanks for your suggestions,here is how it went:- I found a couple of these VM1710 boards and tried one and still nothing. I really wanted to see if power was getting to the camera and anything coming out. I was loo
Electronics Forum | Fri Jul 09 23:45:22 EDT 2010 | dman97
I have a CP642 machine that always gives me a Station 17 or Station 19 nozzle error when the machine selects the 2.5mm 3.7mm or 5.0mm nozzles. It always throws an unknown nozzle station 17 error after all the heads have switched to the above mention
Electronics Forum | Tue Sep 14 17:15:30 EDT 2010 | daxman
Hi Steve, I don't have any experience with CP2's. Sorry .. hazarding a guess though... if they use the analog servo amps like they do in the CP4's, they had a bunch of trimmer pots on them. There is a procedure to zero them using the mecca check mod
Electronics Forum | Wed Jan 19 13:30:37 EST 2011 | bvdb
The user manual says: Cause: A stick feeder part shuttle is in the advanced position where it could interfere with the nozzle. Remedy: Press the [I/O] function key and retract the part shuttle. I don't have a stick feeder. I tried resetting the I
Electronics Forum | Thu Jan 20 07:58:46 EST 2011 | jdengler
Hi Bert, Take all feeders off of the machine. Do a reset start (hold reset switch in while powering up the machine). This will flush the memory so you will need to load PROPER, STATUS, PROGRAM. If it still does it you may have a short in a feede
Electronics Forum | Sun Jan 23 00:57:23 EST 2011 | bvdb
Hi Jerry, Happy New Year. Thanks for your suggestions. You were on the right track because I remembered that one of the last things that happened before the error message started showing up was that I cut and removed the empty tape from the back o
Focusing on the SMT field for more than 15 years, QYSMT has been committed to meeting the needs of customers and partners. Our mission is to provide the best solutions while helping to reduce costs and increase efficiency.
Manufacturer / Equipment Dealer / Broker / Auctions
2nd floor, West side, Building 12, Hengmingzhu Industrial Park, 32 Xiangxing Road, Shajing Tongfu Industrial Zone, Baoan District
Shenzhen, China
Phone: QYSMT / MOREL USA CONTACT – SUSANTA TRIPATHY.: 1-912-373-4005 / China Contact: 86-075521635007