Electronics Forum: fuji cp7 43 e (Page 1 of 3)

fuji IP3 Technicians

Electronics Forum | Fri Aug 02 23:08:43 EDT 2013 | empac

Hi Anil, Can you send me your direct e-mail address ? Thanks. Bob

Re: fuji machin

Electronics Forum | Sun Aug 29 09:03:00 EDT 1999 | Kenny Chew

Looking to purchases: GL-2, GL5, GL541E CP4-3, CP-6 IP-2, IP-3

Recomendations? Fuji CP7 or Univ HSP4797?

Electronics Forum | Sun May 23 19:43:29 EDT 2004 | Alan

Hi Grant, most of my experience is with the range of Fuji equipment, CP's, IP's, QP's. I have not worked with the CP7 yet. With the proper training, Fuji equipment is superb to work with and will run for years. My only Universal experience

Fuji CP6, CP7 feeder calibration manual

Electronics Forum | Tue Aug 18 12:34:43 EDT 2015 | dlee87

I may have what you are looking for but it is a > 244mb file. Thank you very much, can you attach to d.le@electronic-source.com if no matter!!!!!

Recomendations? Fuji CP7 or Univ HSP4797?

Electronics Forum | Fri Jun 04 09:30:43 EDT 2004 | gregf912

Grant, The Fuji chipshooters are built with the same mindset as the hydraulic presses and huge motor lathes that were the CP ancestors. The first Fuji CP was a modified motor lathe. They are solid. I can move a Fuji across the country and not have t

Recomendations? Fuji CP7 or Univ HSP4797?

Electronics Forum | Wed Jun 23 10:05:17 EDT 2004 | exmaintenanceleader

Hi Grant, I'm ex Fuji service engineer I install also at Sagem Czecz Republik (Kladnow near Prague) in 2000 they use at new lines MPM- 2XCP643E and 1xUniversal GSM (French owen (I do not remember the exacly tipe) at second hand line they use 2x and

Can F4G connect with more than 8 CP7 or QP3?

Electronics Forum | Tue Jun 11 15:56:43 EDT 2002 | mjabure

Actually F4G is a programming environment similar to panatools, not a machine, it stands for "Fuji 4th Generation". The connection being questioned is to the communication network, and yes with the proper hardware you should be able to connect more t

Recomendations? Fuji CP7 or Univ HSP4797?

Electronics Forum | Fri Jul 09 16:43:18 EDT 2004 | Sam

If pure speed is the main requirement then I would still not go with Turrent technolgy machines. The FCM from Assembleon (Now AX) is the fastest machine in the industry and consumes much less floor space then any Turret. Gantry machines such as Siem

Recomendations? Fuji CP7 or Univ HSP4797?

Electronics Forum | Mon May 24 12:43:41 EDT 2004 | cyber_wolf

I have worked with Fuji turret machines for several years. I highly recommend them.They are mechanically superb. They very very rarely break. The only draw back from Fuji in my experience is the knowledge of the guys you get when you call the service

Fuji PAM measure

Electronics Forum | Fri Sep 16 12:52:13 EDT 2005 | timekey

Steve- Depending on which Fuji model you have, Fuji PAM either needs to be purchased from Fuji or if you have a CP-7, CP-8 or NXT, Fuji PAM is already installed in the machine from the factory. The kit...if you are required to purchase it from Fuji i

  1 2 3 Next

fuji cp7 43 e searches for Companies, Equipment, Machines, Suppliers & Information

consignment program

High Resolution Fast Speed Industrial Cameras.
Sell Your Used SMT & Test Equipment

Easily dispense fine pitch components with ±25µm positioning accuracy.
Selective soldering solutions with Jade soldering machine

High Precision Fluid Dispensers


"回流焊炉"