Electronics Forum: fuji loading position (Page 1 of 31)

Cp6 mark read position

Electronics Forum | Sat Aug 22 09:59:44 EDT 2015 | linux

Hello all, Can someone tell me the step by step procedure to check xo,yo, mark read position using Fuji board. Cp6 Fuji.

MPM prestop position

Electronics Forum | Tue Jul 05 05:23:34 EDT 2005 | kentes

We have one set MPM AP25. Its prestop position is not stable,but stop position is stable. It often occur "time out" alarm when load PCB.Which one can help us.

MPM prestop position

Electronics Forum | Wed Jul 06 10:22:04 EDT 2005 | PWH

At times we have had this problem with our AP25 due to one of the conveyor belts slipping. Load a PCB and check to see that both conveyor belts are running at the same speed. If not, tighten the one that is dragging. Hope this helps.

fuji CP642 or CP643

Electronics Forum | Tue Oct 02 10:26:17 EDT 2012 | jimmyboz

If I had a choice I would choose a CP642 90% of the time. The loading system on the 643 can load 2 PCBs at the same time but is complicated. If 2 seconds on PCB load time is critical on your production choose the 643, if not, choose the 642.

Entering placement position on GSM's

Electronics Forum | Mon Feb 12 09:44:47 EST 2007 | SWAG

Enhanced board set-up, set conveyor width, load board, (your fiducials must be accurate!), use two fiducials to set reference point, click on placement(s), move crosshair to centerpoint, use two point teach to teach one point in the center or use cor

CAN'T OPEN ANC. invalid place position x

Electronics Forum | Wed Jan 27 08:39:07 EST 2016 | thefinder

Hi to all. i resolved my problem. I just select "LOAD" option the the program run.

smt machine of fuji machine nxtII

Electronics Forum | Thu Oct 02 01:59:06 EDT 2008 | edmaya33

Obviously nobody can help you Jack. 1. its the camera for parts recognition ( enhanced CMOS ). 2. positioning system upgraded from ball screw to linear motor/gantry. before CPH=16500 new CPH=18000 using H12S

Fuji cp6 re-reading fiducials

Electronics Forum | Fri Jul 08 10:11:44 EDT 2005 | Luke Mittur

Hello When the table goes back to loading position, it checks for the avaialbility of the board. It is possible that there is a component right under the PCB confirm sensor and the sensor is not able to recognise the board, so it unclamps . No

Mydata

Electronics Forum | Wed Mar 07 07:08:30 EST 2007 | Rob

They are very long with lots of feeder positions & have a fast tape loading mechanism. They are also easy to use and upgrade, and are cheap on the second hand market. However, on the flip side they are slower (the hydra figures are just dreaming as

CP4 of death

Electronics Forum | Thu Apr 13 10:05:47 EDT 2006 | daxman

Okay fellas...I posted awhile back regarding CP4 and CP6 placement issues. I think we may have figured it out. XO/YO and mark read positions were not correct. However, we have a new problem with the CP4-2. I was running the Fuji board, placing a s

  1 2 3 4 5 6 7 8 9 10 Next

fuji loading position searches for Companies, Equipment, Machines, Suppliers & Information

Voidless Reflow Soldering

Reflow Soldering 101 Training Course
SMT feeders

High Precision Fluid Dispensers
Electronic Solutions

High Throughput Reflow Oven
All Surplus Auction - December 18, 2024

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.
design with ease with Win Source obselete parts and supplies

"回流焊炉"