Electronics Forum: fuji wont power up (Page 1 of 12)

Meridian 1020P servo wont start

Electronics Forum | Thu Jun 26 05:07:19 EDT 2014 | bobpan

On the older machines if the z-axis has springs on them sometimes they get weak and when you open the door the z will not stay up. Before closing the door manually push the z up if they are dropping down then enable the motor power. If this is the ca

Meridian 1020P servo wont start

Electronics Forum | Wed Jun 25 18:19:49 EDT 2014 | guts1872

During machine run, sometimes when we stop to change parts the servos wont start back up. There is a message on the screen that says "Amplifier is resetting power". When that message clears and push the servo on button nothing happens. There is an er

Meridian 1020P servo wont start

Electronics Forum | Thu Jul 10 19:26:21 EDT 2014 | guts1872

It looks like we did have an interlock problem. Maintenance re possitioned them and it seems to have cleared up our problem. For some reason when we close the door, it still wants to reset the Amp power, but if we wait for the all clear in the GUI be

CP4 jerks all axis after power up and reset sw...

Electronics Forum | Mon Apr 16 13:31:36 EDT 2012 | jdengler

Have you tried to restart F4G and/or MCS/30 after flushing the CP4 memory? I have occasionally ran into the comm error after a reset start. Leave the machine on and restart F4G or the MCS/30 whichever normally is hooked up. If it still won't commu

CP4 jerks all axis after power up and reset sw...

Electronics Forum | Thu Apr 12 15:21:12 EDT 2012 | jdengler

Have you tried to do a reset start? When Fuji's act weird the first place to start is a reset start, then re-load the Proper Status and Program. Jerry

CP4 jerks all axis after power up and reset sw...

Electronics Forum | Thu Apr 12 17:49:35 EDT 2012 | rodrigo

I've done the Fuji flush. It does the same thing. We can not load proper again because it does not communicate with either the F4G or MCS/30. I was able to boot into mechanical mode at one point but now I can not do that either. This thing is drivi

CP-642 sometimes does not finish power up sequence. It hangs.

Electronics Forum | Wed Apr 22 12:50:39 EDT 2020 | rodrigo

Hi all, One of our Fuji CP-642 machines has a weird problem. It does not happen every time but often enough that it is a problem. I power up and press start to zero it. The problem is the zero...ing does not finish. It moves the xy-table, D1/D2 table

Fuji IP3E Start up problem

Electronics Forum | Wed Jun 09 10:41:28 EDT 2010 | chrislyttle

We've been having some problems with out Fuji IP2E machine that we've recently bought from a company that is no longer operating here. Since installing it we've encountered a few problems with it starting up. To give you a quick breakdown of its be

FUJI IP3 MFU1 no power

Electronics Forum | Thu Feb 19 12:22:52 EST 2015 | dman97

Hi there. I have an IP3 machine that refuses to power up the MFU cart on side 1. I have already replaced the I/O card but still no dice. Is there a relay or fuse that I need to check to get this to power up? The machine will not operate the camera

FUJI IP3 MFU1 no power

Electronics Forum | Tue Feb 24 15:32:10 EST 2015 | swiese242

Hi there. I have an IP3 machine that refuses to > power up the MFU cart on side 1. I have already > replaced the I/O card but still no dice. Is > there a relay or fuse that I need to check to get > this to power up? The machine will not operate

  1 2 3 4 5 6 7 8 9 10 Next

fuji wont power up searches for Companies, Equipment, Machines, Suppliers & Information

Encapsulation Dispensing, Dam and Fill, Glob Top, CSOB

Training online, at your facility, or at one of our worldwide training centers"
Thermal Interface Material Dispensing

High Resolution Fast Speed Industrial Cameras.
Best SMT Reflow Oven

High Precision Fluid Dispensers
PCB Handling with CE

High Throughput Reflow Oven
Assembly Automation Technology

"Heller Korea"