Electronics Forum: handplacements (Page 1 of 3)

SMT handplacements

Electronics Forum | Sat May 13 17:15:06 EDT 2000 | Alek

I'm trying to find a procedure for smt handplacements& the best way to minimize the handplacments before the reflow process.Any steps should be taken ??

Re: SMT handplacements

Electronics Forum | Tue May 16 04:52:59 EDT 2000 | Eric

What type of component you are handling. Connector or IC.

Re: SMT handplacements

Electronics Forum | Tue May 16 21:25:23 EDT 2000 | Dave F

Alek & Ramon: What are we talking about: * Presentation: Feeders / trays / etc * Pick-up: Nozzels / grippers / etc * Reflowing paste for PTH parts Good luck Dave F

Re: SMT handplacements

Electronics Forum | Tue May 16 11:10:06 EDT 2000 | Ramon I Garcia C

I don,t speak english very well but I,m trying to give my opinion. I have the same problem but with the conecctor, because I have an IP-II and it hasn,t nozzle origin, I think if "I have an IP-III; I can correct this problem" I think maybe we need t

Re: SMT handplacements

Electronics Forum | Tue May 16 06:00:47 EDT 2000 | Wolfgang Busko

Do you have influence on the design process ? Avoid components you are not able to assemble in certain $-limits. A way to put delicate parts on the pcb that your P�n�P isn�t able to place is to add an SMD-manipulator used for manual assembly between

First time with reflow oven....

Electronics Forum | Tue Feb 11 16:27:18 EST 2003 | Chad

Currently we hand-assemble all prototypes, usually quantities less than ten. I mentioned the 5 to 50 number because a client will occasionally request more than ten, which has been handled previously by using an outside contract manufacturer (we are

AOI selection,specifically ViTechnology and Mirtec

Electronics Forum | Mon Jul 17 13:36:55 EDT 2006 | kjeffries

I appreciate your comments regarding the programmability of the Mirtec. What type of SMT machine do you use? How easy have you found it to transfer the SMT profiles to the Mirtec? How do you rate the Mirtec in handling top/bottom, multi-panel asse

BGA Alignment

Electronics Forum | Wed May 02 11:27:17 EDT 2012 | aj

Are you having problems with alignment of BGA's or perceiving that you will have problems. We run thousands and they re-align very well with leadfree if slightly off - Do you handplace all your BGA's? I would imagine there would be cosiderable cos

Equipments required for making SMD PCB's

Electronics Forum | Sat Jun 27 10:10:23 EDT 2009 | ysutariya

I'm not in assembly, but I do know of a technology called Sipad if you are only looking to do small batches. They pre-apply the solderpaste to boards with a light adhesive, which allows you to hand-place components, even micro BGA's and fine-pitch Q

BGA rework stencils ( down to 0.65mm pitch)

Electronics Forum | Mon Oct 14 09:31:46 EDT 2002 | russ

First off, are you planning on placing these parts with your placement machine since you mentioned that you do not have an alignment system for rework? I would be leery of handplacing a BGA into paste by steady hand and craned neck alignment. Seco

  1 2 3 Next

handplacements searches for Companies, Equipment, Machines, Suppliers & Information

Best SMT Reflow Oven

High Resolution Fast Speed Industrial Cameras.
Electronics Equipment Consignment

Nozzles, Feeders, Spare Parts - Siemens, Fuji, Juki, Yamaha, etc...
PCB Handling Machine with CE

We offer SMT Nozzles, feeders and spare parts globally. Find out more
2023 Eptac IPC Certification Training Schedule

IPC Certification Training from the comfort of your home or office
Selective soldering solutions with Jade soldering machine

Training online, at your facility, or at one of our worldwide training centers"
BGA and SMD Rework Stations

"Heller Korea"