Electronics Forum: head won't move 4796 (Page 1 of 2)

up2000 HiE hates me

Electronics Forum | Thu Oct 26 20:32:08 EDT 2006 | foxhound

The squegee blades on the machine won't move down to level whenever I make a program. It has a standard head. I can jog them manually in calibrate mode but when I try to make a program they don't work. Why?

Recomendations? Fuji CP7 or Univ HSP4797?

Electronics Forum | Wed Jan 19 10:44:23 EST 2005 | russ

Although I have not personally run or programmed either the Universal or the Fuji to any great extent, I have worked in factories that have utilized each type. One had 4796 machines and the other used Fuji CP3, 4, 4-2, 6, 643. As an observer I am d

Need help for contact 3AVX

Electronics Forum | Tue Nov 01 09:36:41 EDT 2011 | emeto

THe question is - does that happen on all of your programs or just in one program? If it is just this particular board, it might be some softwaRE limit issue. If it happens on more programs it is a hardware issue and it could be one of the following:

mydata tp9 vs philips topaz

Electronics Forum | Fri Nov 30 00:14:36 EST 2007 | vinitverma

ET, With due regards to your '7 years experience', I must say that in my 11 years experience, this is the first time I am hearing about head replacement on a Topaz. On the Eclipse it is easy for an operator to make a mistake by moving the head manua

SMT transformer misalignment

Electronics Forum | Mon Apr 26 15:48:04 EDT 2010 | markhoch

Sudhir, This part appears to have a lot of mass, thus it may be very heavy. What type of placement machine are you using? Is the PCB held in a fixed place on the table while the gantry moves in the X and Y? Or does the PCB move in the X and Y while t

Help CSM84 mechanical alignment

Electronics Forum | Fri May 04 02:32:10 EDT 2007 | jmelson

Thanks! Well, the procedure in the book says to first calibrate the mech aligner with the beam sensor, but that exceeds the X travel. I guess you can just eyeball it off the nozzles and then use trial and error. While poking around on the machine

HTI Screen Printer

Electronics Forum | Thu Oct 11 09:54:30 EDT 2012 | rgduval

I've inherited an old HTI screen printer, and have been told that it was in operation before it was sent to my shop. I'm now trying to get it working, but, with no knowledge of the printer or the control system, I keep banging my head against it. A

QP-132E // FCM 2

Electronics Forum | Fri May 24 11:46:34 EDT 2002 | tmv

Lot's of good discussion in this string...but I think we've missed a few points. First off...turret machines are more than capable of handling the smaller component sizes (in fact, they are the best)...Machines like the SANYO TCM-3000 or Universal 47

Placement Program Tweaking

Electronics Forum | Fri Nov 02 11:23:52 EST 2001 | dougt

Here's my 2 cents....... I worked for a small company that manufactures pick and place machines and had the task of testing/troubleshooting and the dreaded calibration. These machines used vision for part orentation and have what I considered aweso

Re: Dbl-Sided Reflow Question

Electronics Forum | Fri Jun 02 17:33:51 EDT 2000 | Dave F

Hey CK, we�re all sodder googoo�s ... wanna be gurus Why donchu tell �em not to put sodder in your vias? Er, makit so the sodder won�t flow out of the bottom of the vias and cause dem stalactites? OK OK, here�s wacha do, modify the second side ste

  1 2 Next

head won't move 4796 searches for Companies, Equipment, Machines, Suppliers & Information

Flux-Free Reflow Soldering

Wave Soldering 101 Training Course
Electronic Solutions

High Precision Fluid Dispensers
SMT Machines

Nozzles, Feeders, Spare Parts - Siemens, Fuji, Juki, Yamaha, etc...