Electronics Forum: hook (Page 1 of 17)

Need Assembleon/Yamaha dual shuttle LCS hook motor

Electronics Forum | Tue Jun 12 16:53:56 EDT 2012 | proy

I need a lCS hook motor for an "Xii" dual shuttle LCS. If anyone has an orphan dual shuttle LCS for Xii generation machines please email if I can purchase the part. Delivery is 3-4 wks, will order if I have to, but don't want to wait that long. PR

charging battery with solar power?

Electronics Forum | Fri Dec 01 23:37:34 EST 2000 | Kel

If i hook a 5amp/12volt solar panel to a 6 volt lead acid battery, would it recharge it? is it as simple as hooking the two together? thanks,

Drinking Water In Production

Electronics Forum | Tue Feb 08 03:55:18 EST 2005 | Rob.

We got ours hooked on solderballs - 2 birds with one stone!

Siemens 80 S-20 problem

Electronics Forum | Thu Mar 08 06:30:48 EST 2007 | tommyttr

Chris, The machine is looking for a response from the LC. Usually, it will hang up from a corrupted .gf file. delete all the .gf files from the station. make sure you are NOT hooked up to the LC and/or LC turned off, put machine in stand alone mode.

Low humidity dry cabinets for MSD

Electronics Forum | Mon May 07 15:54:22 EDT 2007 | joeherz

If you're looking for something for less than $5-10k, you should consider setting up a point-of-use air drying system. If you can supply fairly dry air from a house system to the point of use dryer, you can acheive humidty levels below 2% easily. W

Dye and Pry

Electronics Forum | Wed Mar 12 23:00:10 EDT 2008 | davef

You can say: The pad was lifted after reflow and prior to the dye and pry failure analysis. When we see lifted pads, we think: * That's a good solder connection * Either it took a lot of force to lift that pad or the fabrication of the board in the


Electronics Forum | Sat Feb 16 22:19:11 EST 2013 | mdang

Hi, I bought a fuji Flexa v4.6.0.7 and hook it hook it up with CP65 machine. The flexa system already have CP65 configure so I can see the production program on the machine and delete them but I can not transmit a new program to the machine. It error

Paste life span on the printer

Electronics Forum | Wed Mar 14 08:45:41 EST 2001 | stefwitt

In order to track the board flow through your line you will have to hook up all conveyor input sensors as well as the last output sensor to a PLC. You can program the PLC to provide an alarm signal if a accumulative time of xxx hours for any board is

Stenciling chipbonder.....

Electronics Forum | Wed Jan 22 15:22:53 EST 2003 | davef

Hey "Dispenser Boy" does this mean we can have your machine? ;P I'll be out to supervise the packing with a Hook in my hand. Poke around the fine SMTnet Archives to get started on aperture design. 7525, Stencil Design Guidelines is pretty much of

Stenciling chipbonder.....

Electronics Forum | Thu Jan 23 09:17:08 EST 2003 | bdoyle

There's a Red Hook brewery about 40 minutes south of here. I've taken that tour a few times. Don't let Dave fool you though, he's changing tastes and is beginning to import beer from Maine.

  1 2 3 4 5 6 7 8 9 10 Next

hook searches for Companies, Equipment, Machines, Suppliers & Information

Selective soldering solutions with Jade soldering machine

MSD Dry Cabinets
ISVI High Resolution Fast Speed Industrial Cameras

High Resolution Fast Speed Industrial Cameras.
SMT Machines

High Speed Precision In-Line SPI System - Mirtec MS-11
PCB Handling with CE

IPC Certification Training from the comfort of your home or office
BGA and SMD Rework Stations

MSD storage in desiccant dry canbinets