Electronics Forum: hot air dewetting (Page 1 of 64)

debridging hot air knife.

Electronics Forum | Fri Jul 13 05:25:03 EDT 2001 | surachai

I would like to know about the efficiency of hot air knife debridging option with wave solder machine ,anyone use this option please suggestion to me about yield ,side effect or profitable of this option . Thanks.

debridging hot air knife.

Electronics Forum | Sat Jul 14 10:34:42 EDT 2001 | davef

This portion of SMTnet is intended for people whining about the operation of the forums and what-not. A lot of the people asking questions like your use the production forum. We don't have an air knife on our wave, but I recall some threads on SMTn

PWB Pad Finish & dewetting

Electronics Forum | Thu Dec 06 19:46:08 EST 2001 | davef

First, we�re assuming that we�re talking hot air solder leveled [HASL] bare boards, eh? Consider using A-600 - Acceptability of Printed Boards as the basis for discussing the bare board problems. It is the bare board analog of A-610 - Acceptability

hot air rework station / solder paste

Electronics Forum | Thu Nov 16 23:34:56 EST 2006 | mds33200

Hi, I am new in this industry and have purchased a beguinner unut, a 3-in-1 solder, desolder, hot air station. Currently I work on cellphone mainboards. At the moment I only replace single large chips on the mainboard. I would like to be able to repl

hot air rework station / solder paste

Electronics Forum | Fri Nov 17 15:12:26 EST 2006 | mds33200

Hi, I am located in Auburn Mass (USA) right near Worcester. Now I noticed you talked about micro stencil for a populated PCB, would I need one? Or could I use a syringe to lay a tiny dot of paste since im only replacing a chip or 2 (at the moment)? I

hot air rework station / solder paste

Electronics Forum | Fri Nov 17 14:42:06 EST 2006 | billwestiet

Mark, This is a big topic. Where are you located, it would probably be best to hook you up with someone in your area. Anyhow, lead or lead free should be based on whether the circuits are lead or lead free. I would guess that cell phones would all

hot air rework station / solder paste

Electronics Forum | Fri Nov 17 16:24:18 EST 2006 | billwestiet

I'm in North Attleboro, small world. To answer your question, you can deposit small dots of paste with a syringe. Kind of tricky work, and there are small stencil soluions out there fairly inexpensively. See http://www.minimicrostencil.com/ (I do

SMT-1160 (1102) hot air pencil OK Ind PUMP KIT?

Electronics Forum | Thu Jul 10 22:41:56 EDT 2008 | davef

Did you try here: http://cgi.ebay.com/OK-INDUSTRIES-INC-SMT-1160-HOT-AIR-SOLDERING-SYSTEM_W0QQitemZ130237552185QQihZ003QQcategoryZ26261QQssPageNameZWDVWQQrdZ1QQcmdZViewItem

SMT-1160 (1102) hot air pencil OK Ind PUMP KIT?

Electronics Forum | Wed Jul 02 12:49:57 EDT 2008 | jlbelectronics

Hi all, I have a OK industries hot air pencil model number SMT-1160 even though the label on the base says its a SMT-1102. The problem that I have is that the Diaphragm (diafram) has ruptured inside the small internal air pump. Where can I get a p

air nozzle

Electronics Forum | Tue Dec 08 08:36:34 EST 1998 | k pearson

I HAVE SEEN ADVERTISED AN AIR NOZZEL THAT USES COMPESSED AIR TO SPEW OUT EITHER HOT OR COLD AIR. I HAVE NEED OF SUCH A DEVICE. I DO NOT HAVE THE MANFR. OF THESE. ANY SUGGESTIONS ??

  1 2 3 4 5 6 7 8 9 10 Next

hot air dewetting searches for Companies, Equipment, Machines, Suppliers & Information

Encapsulation Dispensing, Dam and Fill, Glob Top, CSOB

Smt Feeder repair service centers in Europe, North, South America
convection smt reflow ovens

We offer SMT Nozzles, feeders and spare parts globally. Find out more
SMT feeders

High Precision Fluid Dispensers
2024 Eptac IPC Certification Training Schedule

High Throughput Reflow Oven