Electronics Forum: hydra motor amplifier a (Page 1 of 4)

my12 motor amplifier channel a error

Electronics Forum | Wed Jan 29 13:01:04 EST 2014 | tech1

Back when the Linear Y wagons first came out Mydata had problem with the original Y amplifier and were swapping out the complete box for customers who had problems. There was also a problem with the encoder that resulted in the same type of errors yo

my12 motor amplifier channel a error

Electronics Forum | Wed Jan 29 18:41:22 EST 2014 | alphatronique

Hi did you look for mechanical issue like friction somewhere ? when init i use very low force buy much more while running that may explain wly machine work in production fur fail only on init i face that whit flex cable that make just little fr

my12 motor amplifier channel a error

Electronics Forum | Fri Jan 10 03:33:42 EST 2014 | hans88

hello people, we have a my12 wich has a problem it gives the following error during hardware initialization: F-MOT-MSETDYN Y/1236 :Motor amplifier channel a error. after this error it says hardware initialization failed. this prevents us of using

my12 motor amplifier channel a error

Electronics Forum | Fri Jan 10 15:33:57 EST 2014 | hans88

Hello Rob, Thanks for your fast reply. I will check the parts you mentioned. You were right about the mot card we swaped it with a new one but that made no difference. Today we tried to find were the problem could be we: - removed the j1, j2 and

my12 motor amplifier channel a error

Electronics Forum | Fri Jan 10 11:32:52 EST 2014 | rgduval

Hi, Hans, I would have suggested swapping the MOT card out to see if that fixes the issue (or, changing the MOT card with another one to isolate the card), but, it sounds like you've already done that. I'm surprised that MyData would point you towa

Mydata Lift motor 2 amplifier error

Electronics Forum | Thu Oct 15 10:21:30 EDT 2015 | azdback

troubleshooting a table lift error on MY12. Error code: F-MOT_Releaseboard conveyor lift/1304. Basically, the table got stuck on the up position. Also bench tested both lift motors and they are ok.Rotated the lift motors manually to test the encoder

MY9 Hydra errors ( solved )

Electronics Forum | Wed May 13 15:57:43 EDT 2020 | azdback

We have been working on an intermittent error on our hydra. And it seems to happen only after several hours of production have passed, it doesn't happen during the first part of the shift. Our hydra goes from working fine for several hrs to making

MY12 HYDRA issu

Electronics Forum | Mon Dec 26 18:02:37 EST 2022 | rgduval

So, your Hydra Z message timed out... A couple of potential causes: 1. Hydra MOT card failure 2. Hydra z-motor failure 3. Hydra z-motor encoder failure 4. Hydra z-lock failure 5. Disconnected cable 6. X-wagon cable Start by booting into service mod

MYDATA HYDRA Z/156 error on Hardware Intialization.

Electronics Forum | Wed Mar 04 12:51:41 EST 2020 | bk

That error means your hydra z did not reach it's specified position. With the machine on you should be able to manually push the hydra down and let it come back up. Make sure it isn't being held up or hitting anything as goes down. Lots of times a pa

MPM Sigmaprint 400

Electronics Forum | Tue Mar 28 19:43:49 EDT 2017 | aemery

Simon, Trying to dust off my 400 knowledge here, I can picture the 500 and 1500 better in my head. I think the 400 also has a Z axis amplifier box in the back of the machine. Remove the rear lower door and pull out the big square vacuum box. If it

  1 2 3 4 Next

hydra motor amplifier a searches for Companies, Equipment, Machines, Suppliers & Information