inch

"inch" search results in the Electronics Forums



756 results found for "inch" in the Electronics Forums

Order by: Relevancy |   Date

Universal Genesis Inline7

Nov 16, 2018 | It turns out the issue was programming in milimeters instead of inches.

PCB routing

Aug 30, 2017 |

Thick Film Screen Printer

Aug 15, 2016 | The screens are basically the same technology. But when I worked with them , the screens were 6 inch

SMEMA Conveyor into Reflow Oven? How to handle end of line signal.

Dec 30, 2015 | Tom, Mount one sensor at about 6 inch inside of the beginning of the oven conveyor and use its ou

Halogen-free Solder Reflow Quality Issues

Nov 6, 2015 | They're probably 12 - 18 inches, maybe slightly longer.

Soldering to hard gold

May 2, 2013 |

Fuji FCP 2 Check Servo issue

Sep 16, 2010 | Thanks for the response Travis. I'd think the table would inch or move if it were stuck inching key

Fuji FCP 2 Check Servo issue

Sep 14, 2010 | I would check for stuck inching keys.

LGA processing

Aug 9, 2010 |

screen blade length

Sep 2, 2009 | I have always gone with blade length equal to board width plus 2 inches - 1 inch either side. Is the

Lead Free finish

Nov 3, 2008 | Vlad, That was a bad statement to make... Enig should never be thicker than 5 micro inches max

Gold thickness

Jul 15, 2008 | Hi Aj, Recommended Immersion gold thickness would be 3-5 Micro inches over 140 -200 micro inches

BGA reflow on bottomside

Nov 20, 2007 | It can be done. But as Rob states, use edge rail oven. We have a product 18 inches long by 9 inche

BGA Reflow Profile

Oct 31, 2007 | Hi, My oven has 5 zones each 12 inches in length , giving a total of 70 inches Heating Zone in to

MPM SPM Supplies

Feb 23, 2007 |

Ads Getting Piggy Again

Feb 13, 2007 |

SMD flatness standard

Nov 20, 2006 |

SMD flatness standard

Nov 18, 2006 | Bow & twist: IPC-A-600. Acceptability of Printed Boards 1.5%; Goal 0.005" per inch; Practicle 0.007"

Forums a bit ugly

Sep 24, 2006 |

I am looking for a SMT machine that will handle a large board

Sep 12, 2006 | I am looking for a Surface Mount Machine that can handle a board that is 24 inches long and 7.5 inch

thermocouple wire

Jul 20, 2006 | when I order a thermocouple wire for doing oven profiles, it comes in a standard length of 36 inches

Gold Thickness

Jun 9, 2006 | You can not solder to 30 micro inches of gold over nickel and certainly not 80 microns. You can not

Gold Thickness

Jun 9, 2006 |

Gold Thickness

Jun 9, 2006 | We have a board calling out for 50 micro-inches of nickel over 30 micro-inches of gold. This is a so

BTU oven info

Feb 24, 2006 |

MyData TWM

Jan 18, 2006 | What I mean by it does not work is after I moved the brackets I have about 4.5 inches from the end o

Fuji IP1 help requested

Dec 15, 2005 | We own a Fuji IP1 with all the manuals, etc. but can't figure out how to inch the tray robot. We ca

Water Jet Stencil Cut

Oct 4, 2005 | Am I doing my maths right? 0.005 inches is 0.127mm which is crap for a stencil. Our supplier (laser

SMT MACHINES

Sep 29, 2005 | Any suggestions on a good pick n place machine that can handle boards over 20 inches long?

0402

Jun 7, 2005 | We use a 0.012 inch gap betweem 0402 pads.

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Chromatography

Reflow Oven