"insulator" search results in the Electronics Forums

245 results found for "insulator" in the Electronics Forums

Order by: Relevancy |   Date

How to identify any Vibration Source in Reflow Oven

Aug 2, 2019 | A recording accelerometer is about the only thing I can think of. Unless you can find an insulative

TS-2414-V Insulating Varnish

Aug 1, 2019 | Is TS-2414 insulating varnish material suitable for conformal coating of PCBAs? How can its performa

Ground straps and dress shoes

Dec 28, 2017 | Leather is not very insulative. AFAIK a lot of good quality dress shoes are naturally ESD safe. (or

It does say Electronics Forum

Oct 6, 2017 | potting the board with epoxy will make it non repairable the same insulation effect you would achie

ESD Chair

Apr 19, 2016 | In ESD-head parlance, chairs are "Process Required Insulators." Checking PRMs once every 3 months is

DEK Horizon 03i

Sep 16, 2014 |

Wire soldered directly on the PCB

Jun 28, 2013 | I don't see any requirement for a ferrule on the wire. As long as your insulation clearance is twic

electrovert Omniflow 10

May 7, 2013 | Hi Hege, there is insulation, which when you look at looks pretty stable.I suspect that there is

electrovert Omniflow 10

May 7, 2013 |

Test clip connectors

Mar 19, 2012 | Those are IDC (Insulation displacement connector) you can make them yourselves. you can get the stuf

PCB racks

Aug 9, 2011 | I used InsulFab to make some for me in the past, ran into the same issue. They did an excellent job

Homebrew vapour phase...?

Jun 19, 2010 |

Heat insulating box...

Jun 13, 2010 |

Heat insulating box...

Jun 8, 2010 |

Heat insulating box...

Jun 8, 2010 |

Heat insulating box...

Jun 7, 2010 |

Heat insulating box...

Jun 7, 2010 |

SMD Adhesives Gluing Process

Sep 10, 2009 | The adhesive should be a dielectric (insulator) by design, if not it could possibly short across lea

ESD....Limiting Resistor

Jul 1, 2009 |

ESD....Limiting Resistor

Jul 1, 2009 | So, would putting insulating pads on the test fixtures without pads make this issue go away?

ESD....Limiting Resistor

Jun 30, 2009 | Dave, We have both situations where the grounded electrical equipment on the mat has insulative pad

ESD....Limiting Resistor

Jun 29, 2009 |

Thermocouple soldering

Jun 23, 2009 | I don't know about removing the teflon insulation, but we weld our thermocouples.

RoHS round 2

Mar 27, 2008 | I don't think it matters. Without insulation (did you see the plastics listings?) it's kind of a moo


Mar 7, 2007 | Have you considered replacing the insulative latex with disipative rubber matting?

battery pad

Feb 28, 2007 | Some no-cleans will pool flux on the top of the solder joint which acts like an insulator. I normal


Feb 14, 2007 | Latex is not a conductor. It's an insulator. So, it will not conduct a charge to the metal wire ra

finger print

Jan 3, 2007 |

pcb smt pad replacements

Oct 17, 2006 | ya don't need no stinkin pads. just run sum fine gauge insulated jumpah wires from da I.C. legs (da

ESD flooring and footwear

Oct 11, 2006 |

Soldering Help

Jul 11, 2006 | 1) Use insulated wire & only strip back as much as you need for a good joint. 2) Wrap insulation

Soldering Help

Jul 10, 2006 |

White residue inside the reflow oven

Apr 13, 2006 | I had something similar a while back it looked like fibreglass insulation in my case (was using no c

Pages: 1 2 3 4 5

pcb components vacuum pick up

 Reflow System