Electronics Forum: ipc-tm-650 and method and 2.1.2 (Page 1 of 1)

warp and twist

Electronics Forum | Tue Feb 14 09:10:43 EST 2017 | davef

Assuming the traces run parallel and perpendicular to each other, I'd choose one direction the traces run as "x" and the other direction for "y." Then I'd pick a unique identifier on the board to insure proper orientation. Next, I'd measure warp and

Bow and twist of PCB's

Electronics Forum | Mon Apr 23 14:03:18 EDT 2001 | Ryan Jennens

Dougie- We,too, have the IPC-A-600F, and the spec. refers to IPC-TM-650 test method in the back of the book. Look on page Number 2.4.22 of the test methods appendix. This outlines the procedure for determining the percentage of bow and twist,

Bow and twist of PCB's

Electronics Forum | Fri Apr 20 07:12:22 EDT 2001 | wbu

Dougie, oh yes, it�s a bit short that chapter. I have the Revision e in front of me and this one contains in the appendix the needed IPC-TM-650 Test method for bow and twist. Can�t think that they don�t have that in the new revision. Hope you find

PCB assembly bow and twist

Electronics Forum | Thu Dec 26 12:12:55 EST 2013 | igorfo

Dear Friends, I need your help to understand requirements and measurement methods for bow and twist of assembled PCB (PCBA have and SMT and TH components). I already check all posts on the site but didn't found any related to my question answers.

force between the pad and laminate material

Electronics Forum | Wed Jun 12 08:13:29 EDT 2002 | davef

Don't sound proper. There is no specification. Pad peel strength test methods are: * IPC-TM-650, Method 2.4.21 for multiple solderings * IPC-TM-650, Method 2.4.8 for copper peel with a Instron machine. Typical requirement for Cu is: 6 lbf/in [1

Bow and twist of PCB's

Electronics Forum | Fri Apr 20 05:32:39 EDT 2001 | dougie

Hi, I've just splashed out �60 on IPC-A-600F trying to find out the formula for measuring the bow and twist of raw PCB's. Much to my dismay there are 10 lines on the subject in the whole standard. Worse still is that it tells me nothing I don't alre

Re: Shear strength and Copper/Tin Intermetalic layer

Electronics Forum | Thu Jul 09 21:04:50 EDT 1998 | Dave F

Hi there, I am looking for some informations concerning the shear or pull strength of a typical TQFP 20 mils leads in relationship with the Copper/Tin intermetalic layer thickness. Could anyone help? Thank in advandce. rgs, chiakl Chiakl

Standard of PCB Bow and Twist in Incoming Inspecion

Electronics Forum | Thu Feb 27 12:27:10 EST 2003 | stevel

Hi all, We got some bare pwb in our incoming inspecion looked really wrapped. The maximum twist of the pwb we messured is 0.056inch by following the method in IPC-TM-650 2.4.22 C. (The diagonal size of our pwb is 7.5inch) According to the IPC standa

Foam fluxer maintenance, storage and cleaning

Electronics Forum | Sun Nov 08 15:27:25 EST 2015 | davef

Thinner: Flux thinner, NOT paint thinner We kept a spare stone in thinner in inventory. We cut PVC pipe to size, cap in one end, screw thread on the other, stone inside, filled with flux thinner and covered with a screw cap. I don't remember who we

  1  

ipc-tm-650 and method and 2.1.2 searches for Companies, Equipment, Machines, Suppliers & Information