late

"late" search results in the Electronics Forums



481 results found for "late" in the Electronics Forums

Order by: Relevancy |   Date

DEK265 Infinity

Feb 18, 2020 | We are having a few issues lately with a Data file open error on the printer and also the belts carr

Is SMTnet Running Slow?

Jan 30, 2020 | Dave, I am glad you asked. Lately site is slower. I use mainly the forum, so this is what I can spe

solder defect

Sep 20, 2019 | hello, I have been experiencing a strange solder defect lately. hope some of you may know what is ca

Any TWS QUADRA P&P FOR SALE??

Sep 17, 2019 | Hi,sorry for late reply DO you still has feeder to sell? If yes èlease let me know type and money re

SMTech MV100 printer schematics

Jul 14, 2019 | Does anybody have it? Our printer started to act strange lately. I have user manual, but that's not

I need of SMT-Maestro install files

Jan 10, 2019 | Super late reply, but I just went through the same hunt and thought I'd post the files for posterity

0201 placement by Fuji CP643 Machine

Jul 27, 2018 | Just found my notebook from the late 90's, 643 confirmed 0201 from the factory, 642 needed the upgra

unmarked chip resistors

Sep 8, 2017 |

pcb manufacturing

Jan 8, 2016 | hi, hope I'm not too late for your attention. suggest you http://www.pcbgogo.com/b, just 12usd, 2-3d

Japan Unix Destop Soldering Robot

Mar 23, 2015 | Hi George - Better late than never. Nice units but also look at the cost of weekly consumables. Apol

Juki Position Board System Error

Feb 24, 2015 | We are getting a position board system error more and more just lately on a FX1 that we have, anyone

DEK Nano-Protek against Aculon Nanoclear

May 28, 2014 | Hello all, I used DEK Nano-Protek and lately I hear about Aculon Nanoclear to be doing exactly th

PoP parts

Apr 30, 2014 | Thank you all for the posts. From all I read lately I will probably try a different solder paste and

Is it just me?

Apr 28, 2014 |

cracked joints

Jul 18, 2013 | Thanks for that, sorry Im late setting (set by someone else) Speedline Bravo Top 1st cham

Dehaart EL20 Semi auto

Jun 5, 2012 | Haven't seen one of these since the late 80's. You should get a new one. If you are a semi auto guy

Senju wave opinions?

Feb 21, 2012 |

FLexJet pickup problems

May 12, 2011 |

Assembly/Stuffing Issues

Jan 14, 2011 |

Reflow Oven Cool down

Sep 17, 2010 | Our facility is typically a high mix low volume site, but lately we are getting increments on our re

BIRAL Lubricants

Jul 6, 2010 | Hi, sorry for the late reply. We use Mobil Mobilux EP2 grease for the LM blocks and TFL50 where t

ceramic cap crack

Jun 19, 2010 | Hi all, lately ofen I have problem with cracked ceramic capacitors.We use 0805 and 0603 cap. Samsun

ICT and specifying PCBA testing

Mar 24, 2010 | Ignore the defect * Late 1990s to early 2000s => ICT * Early 2000s to mid-2000s => MDA * Mid-2000

smd led storage

Mar 18, 2010 | hi, lately I have problem with smd leds.After reflow 2-4% of leds are broken.I think , that reason

BTU Reflow Oven

Oct 23, 2009 | sorry about the subject, it was late last night when i posted. what kind of thermocouples? i wil

Soldering issues lately!!

Sep 13, 2008 |

Soldering issues lately!!

Sep 12, 2008 |

Soldering issues lately!!

Sep 11, 2008 |

Soldering issues lately!!

Sep 11, 2008 |

Soldering issues lately!!

Sep 11, 2008 |

Soldering issues lately!!

Sep 11, 2008 | Is just me, or too many "soldering issues" have been observed lately? on this forum... could be a ~9

LINEAR VOLT REG Polarity diagonally opposite

Aug 11, 2008 | Well first 6 out of 180 were right and acceptable RTI result was supplied too late, I was busy on in

Using older LCS with New Opal II

Aug 10, 2008 | I am told that an older LCS (mid/late 90's) is NOT compatible with a new OPAL, can anyone confirm th

What happens to LPI Solder Mask on the RF4 PCB During Reflow?

Apr 21, 2008 | Hi dave, sorry for my late reply...right now do not have info about the LPI and I'm not allowed t

Kester Paste from Mexico

Nov 24, 2007 |

SMT adhesive suggestions?

Jul 17, 2007 | Yuppers. Back in the "late '90s" at my last company, we, too, used loctite's chipbonder with our GD

PLCC 44 and QFP 240 tilting problems

Feb 19, 2007 | Are your pads on the board aligned correctly? I've seen this a lot lately. Pads on opposite sides

Stencil Fiducials

Feb 15, 2007 | CK, That is the exact machine I had. I bought a Dek 265LT in 1997 or late 96. Was one of the fi

Flux residue cause high false reject at ICT

Dec 7, 2006 | Hi all, Sorry for the late reply..I am sure it is flux residue..Found no such symptom as Grey men

removing glued chips

Nov 8, 2006 |

removing glued chips

Nov 8, 2006 |

BGA Solder Acceptance Criteria

Aug 30, 2006 | Dear Davef, Sorry for late reply! CMK is a PCB supplier, BGA solder defect were found in CMK PCB.

Next Stages of Lead Free

Aug 11, 2006 | Hello Hey Wood! I have to say Bismuth is a no-no for late night snacking. Although it is low in

New SMT line - P&P equipment selection help

Jul 3, 2006 | Hi, Bit late for the sales thing, I think. Grant

New SMT line - P&P equipment selection help

Jun 28, 2006 | Scott, Over a year late.......give some notice to the date's of the original post.

Pages: 1 2 3 4 5 6 7 8 9 10

Ecolloy Soldering Alloy

SMT Pick and Place