Electronics Forum: led calibration (Page 1 of 2)


Electronics Forum | Thu Jan 06 06:09:43 EST 2005 | calibration

does anyone know of a LED test solution for multiple LEDs' on a PCB that can be used in an incircuit or a functional fixture

Resistance laser cutting

Electronics Forum | Fri May 11 03:55:22 EDT 2007 | lupo

Hi everybody, Please could anyone shed any light on the subject: resistance laser cutting with flux- calibration of LEDs during electronic assembly phase. Should special equipments be used? What is exactly the process? Thanks and Regards,


Electronics Forum | Wed Mar 21 13:39:11 EDT 2018 | tombstonesmt

I know this isn't a choice from what I'm reading, but we use to kill LED boards with an old Panasonic MSR. Our newer CM-602 and NPM could not beat the speed when you're talking about a max of 3 different part numbers; depending on binning. My .02 .

Life Expectancy

Electronics Forum | Fri Oct 12 09:16:21 EDT 2018 | directx995

Hello, We are EMS and we are using Unviersal Instruments machines, we have few GC60 and GC120. You didn't mention how old machine is, which is very important. Regarding picks, our GC120 do around 1 million picks PER WEEK when we are running LED proj

MyData tool damage

Electronics Forum | Wed Jan 05 11:26:15 EST 2005 | cyber_wolf

Then Z MOTOR > Then select>CALIBRATE FORCE SENSOR NOTE: you must have a tool in the head when you do this.(Without the tip/spring pushed in) After this calibration the force should drop to 0 when you push in on the spring loaded tip. 2.) Replace th

Yestech B2 Aoi Brightness, how do I adjust?

Electronics Forum | Fri Oct 05 08:46:19 EDT 2018 | babe7362000

I was unable to calibrate the Brightness step. The Pot was adjusted but would not brighten any further than 42. Im thinking I will need a new board or if someone knows what LED part number is used? Any information would be great. Thanks

MyData tool damage

Electronics Forum | Mon Mar 06 11:13:08 EST 2006 | fredericksr

I ran this same process by MyData when I was there for training and I received the message that calibrating the force sensor through the service menu was an invalid technique. Correct me if I am wrong, but every tool should recalibrate itself when i

Panasonic NPM-W Nozzle error

Electronics Forum | Thu Jan 03 15:53:28 EST 2019 | cbeneat

We did figure out the issue. The plastic cover inside the LED lighting unit had a slight film covering it, which made the picture slightly hazy. We had to disassemble the LED module to get at it, cleaned it and it was fine. I didn't think this would

Quad QSV-1

Electronics Forum | Tue Nov 25 08:36:32 EST 2014 | bobpan

Tep stands for the transport card. The board is located in the front bottom left of the machine and should be by itself and have green and red leds lit on the top of it. I would try to reseat the card and then try to reboot the machine. If the proble

Electrovert - MiniPak 300, FDC 450 controls, setting Threshold

Electronics Forum | Thu May 31 18:21:09 EDT 2007 | jamesm

Revelation Industries has an Electrovert MPK1-24774. The manual lacks sufficient information to troubleshoot and fix this problem: Reference: Minipack 300 Wavesoldering System 1986 edition, pg, 18, fluxer, Threshold adjustment. After completin

  1 2 Next

led calibration searches for Companies, Equipment, Machines, Suppliers & Information

SMT feeders

Training online, at your facility, or at one of our worldwide training centers"
One stop service for all SMT and PCB needs

World's Best Reflow Oven Customizable for Unique Applications
Selective soldering solutions with Jade soldering machine

High Resolution Fast Speed Industrial Cameras.
design with ease with Win Source obselete parts and supplies

"Heller Korea"