Electronics Forum: led quad light ring (Page 1 of 2)

Quad IV-c with really dark camera

Electronics Forum | Tue Oct 09 06:14:48 EDT 2018 | bobpan

Move the camera over a feeder position and shine a flashlight to see if the image improves.....if it does....your light ring needs replaced or the led's need replaced in it. Sometimes just re-adjusting the angle of the led's in the ring can help. Go

Quad IV-c with really dark camera

Electronics Forum | Tue Oct 09 05:38:29 EDT 2018 | dfl

Hi, my Quad IV-c is showing a really dark image on the camera and its VERY difficult to see the components pads to make the adjusts. I already check the monitor brightness (at maximum and I can see the crosshair, so the monitor is good) and already

DEK 260 LEDs

Electronics Forum | Mon Jan 30 17:42:50 EST 2017 | jrr3434

A few of the LEDs on the cameras of my stencil printer are really dim. I want to replace them and not have to buy a whole new light ring board. Does anyone know what kind of LED they are? Any info would be appreciated. Thanks.

Fiducial Recognition

Electronics Forum | Wed Jun 13 01:01:10 EDT 2012 | isd_jwendell

I clean all fids with a fiberglass brush pencil so that I know there will be no rejects (it doesn't take too long). The problem is the machine lighting. My Essemtec machine uses a light ring (red LEDs) around the cam. Here's one of many documents th

Quad Upward Vision Issue

Electronics Forum | Fri Nov 06 15:42:58 EST 2015 | sdmideas

I am having a darn hard time getting my upward vision to successfully inspect a ssop14 package. I have created a part profile as defined by the manual as I understand. I believe the profile is ok based on comparison to like parts referenced in the q

Quad 4c not placing components

Electronics Forum | Wed Sep 04 12:50:40 EDT 2019 | smrsteve

Thanks for that Steve - I'll try anything at the moment, but that sounds like a reasonable suggestion. I've already replaced a few cables that looked dodgy, and the LEDs on the LED rings, but I've not done a ribbon cable on the head yet. I shall hav

Quad IV-c with really dark camera

Electronics Forum | Tue Oct 09 10:29:47 EDT 2018 | dfl

Thanks Bob. Using a flashlight helps a lot, indeed. Is "re-adjust the angle" just a bend on the LEDs heads (by hand)? I will try. To replace de LEDs, can I use white ones? I believe with the reds I get less light than whites, but maybe the camera ne

MPM Momentum Vision issue

Electronics Forum | Sun Aug 28 23:53:58 EDT 2016 | aemery

I don't think there is a camera off message in the software, but I might be wrong. So I am making a bit of an assumption here that you didn't have a displayed image and your error was a fiducial not found error. I am also wondering if you decided to

FUJI IP3 MFU1 no power

Electronics Forum | Thu Feb 19 12:22:52 EST 2015 | dman97

Hi there. I have an IP3 machine that refuses to power up the MFU cart on side 1. I have already replaced the I/O card but still no dice. Is there a relay or fuse that I need to check to get this to power up? The machine will not operate the camera

Quad IQ feeder schematics or help ?

Electronics Forum | Fri Nov 06 20:43:58 EST 2020 | jmelson

Does anyone have schematics for the PC board inside a Quad IQ feeder? I have one that worked a few days ago, but now gives me blinking lights and doesn't move. Or, do you know what to do when it won't move? I have checked the contacts and the feeder

  1 2 Next

led quad light ring searches for Companies, Equipment, Machines, Suppliers & Information

convection smt reflow ovens

Easily dispense fine pitch components with ±25µm positioning accuracy.
Sell Used SMT & Test Equipment

Have you found a solution to REDUCE DISPENSE REWORK? Your answer is here.
thru hole soldering and selective soldering needs

Software for SMT placement & AOI - Free Download.
High Throughput Reflow Oven

Training online, at your facility, or at one of our worldwide training centers"


High Resolution Fast Speed Industrial Cameras.
Fully Automatic BGA Rework Station

SMT & PCB Equipment - MPM, DEK, Heller, Europlacer and more...