Electronics Forum: lift and motor (Page 1 of 7)

Mydata Lift motor 2 amplifier error

Electronics Forum | Thu Oct 15 10:21:30 EDT 2015 | azdback

troubleshooting a table lift error on MY12. Error code: F-MOT_Releaseboard conveyor lift/1304. Basically, the table got stuck on the up position. Also bench tested both lift motors and they are ok.Rotated the lift motors manually to test the encoder

Dye and Pry

Electronics Forum | Wed Mar 12 23:00:10 EDT 2008 | davef

You can say: The pad was lifted after reflow and prior to the dye and pry failure analysis. When we see lifted pads, we think: * That's a good solder connection * Either it took a lot of force to lift that pad or the fabrication of the board in the

Transmitter and Recievers

Electronics Forum | Thu Oct 21 16:08:16 EDT 2004 | Dzyna Kid

Does anyone know of any resources I could investigate to make a small circuit that would consist of a transmitter, receiver, and a motor. I want to be able to press a button on a remote control and that would make the motor turn on, then I want to b

Pick and place labels

Electronics Forum | Thu Sep 23 11:50:54 EDT 2004 | JB

We are using a standard nozzle Once placed, the label is not flat, the ends of the label are slightly lifted on both ends. The label is .650 x .200 Have you guys run into a similar problem?

Dye and Pry

Electronics Forum | Thu Mar 13 01:42:58 EDT 2008 | Sean

Thanks Real Chunks and Davef...Yours input is valuable to me. My inputs towards your question asked below: Questions are: * Why did you tell us the following? "This BGA is installed with heatsink (with hook at both side of the heat sink) manually b

Transmitter and Recievers

Electronics Forum | Fri Aug 05 14:42:06 EDT 2005 | B R Proctor

hi their In south africa, we manufacture recievers that work with a remote. They can be used in a simple circuit to control a motor. Best regards Barry Proctor e-mail :zaza@wol.co.za

PFMEA and SPC/Cpk program

Electronics Forum | Thu Mar 02 15:42:30 EST 2006 | russ

in addition to Amols comments I also like Minitab. For FMEA Ford motor Company has a great FMEA program

Tp9 and Tp9 ufp

Electronics Forum | Tue Oct 25 15:03:48 EDT 2011 | sjs2303

Hi Bert, For your second issue, are the tools well lubricated? If not the Midas head can fail to grab the tool and can generate the z motor error. Doing this followed by a base-centre level measurement should resolve your problem. Steve

Skewed and popped components

Electronics Forum | Wed Sep 24 08:34:57 EDT 2003 | stefwitt

Even when you run a board several times, the machine may not make the same travel path every time. This in itself does not create a problem, but the vacuum on the nozzles could be different, dependent on the configuration of components on the heads.

Dye and Pry

Electronics Forum | Wed Mar 12 07:33:40 EDT 2008 | callckq

Hi All, One PCBA failed test after went through the Shock Test(Vibration) and suspected to be BGA solder ball crack. We performed dye and pry and found PCB's pad lifted with red mark ink penetrate pad underneath, what does this mean? Can I say the

  1 2 3 4 5 6 7 Next

lift and motor searches for Companies, Equipment, Machines, Suppliers & Information

SMT & Related Equipment - Delta Tau Data Systems Inc.

Component Placement 101 Training Course
pressure curing ovens

Best Reflow Oven
convection smt reflow ovens

World's Best Reflow Oven Customizable for Unique Applications
PCB Depanelizers

Low-cost, self-paced, online training on electronics manufacturing fundamentals