Electronics Forum: located (Page 1 of 221)

SMT kitting help, losing reels, can't find them, tracking parts located in saved setups, etc

Electronics Forum | Mon May 24 16:08:43 EDT 2021 | robl

Can you have the SMT lines or feeder carts as "stock locations" on your system and issue them to that location? then at least when you go to your pick list you'll know where it is. That's assuming you can do this quickly.

where be located while embed the thermocouple into PTH hole ?

Electronics Forum | Thu Sep 09 07:56:28 EDT 2004 | mksslcheng

A fresher goes in SMTonline ,I would like to learn the knowledge that how to embed and high temp. solder thermocouple into PTH hole while profiling board ,where the bead of T.C be located ,whether in PTH hole or protrude the bottom surface of board .

where be located while embed the thermocouple into PTH hole ?

Electronics Forum | Tue Sep 14 08:16:37 EDT 2004 | davef

Try: 7530 - Guidelines for Temperature Profiling for Mass Soldering (Reflow and Wave)

SMT kitting help, losing reels, can't find them, tracking parts located in saved setups, etc

Electronics Forum | Sun May 23 22:07:43 EDT 2021 | needsmthelp

Hello, I recently became the SMT supervisor where I work. I have experience in much of the other areas but haven't actually done SMT work myself. An ongoing issue that I'm having is parts/reels related. If the person responsible for kitting starts g

SMT kitting help, losing reels, can't find them, tracking parts located in saved setups, etc

Electronics Forum | Mon May 24 03:21:33 EDT 2021 | sophyluo1985

Hi,I'm QUINN form GOLDLAND China,What you should say is Intelligent warehouse management system (MT-WMS) solution;

SMT kitting help, losing reels, can't find them, tracking parts located in saved setups, etc

Electronics Forum | Mon May 24 22:54:34 EDT 2021 | SMTA-64387687

Take a look at Inovaxe.

SMT kitting help, losing reels, can't find them, tracking parts located in saved setups, etc

Electronics Forum | Thu Jul 01 19:13:48 EDT 2021 | SMTA-64387161

Welcome to SMT! I highly recommend exploring the process of adding unique reel identifiers to your reels and tracking locations, or even kitting, using these barcodes. You may also see this referred to as serializing or license plating. Implementin

SMT kitting help, losing reels, can't find them, tracking parts located in saved setups, etc

Electronics Forum | Mon May 24 17:01:22 EDT 2021 | emeto

The good solution is to adopt ERP system and barcode tracking for everything you have in inventory. If not, SMT supervisor will keep super complicated excel sheets to track what is where..... Or.. you can request all to be kitted together and confirm

SMT kitting help, losing reels, can't find them, tracking parts located in saved setups, etc

Electronics Forum | Thu Jun 03 01:26:06 EDT 2021 | deanm

This may seem off the wall but I've seen it work in the past. It is a visual management system without the need for barcodes or spreadsheets. Obtain quantities of different colored clothespins. When a reel is taken out of inventory, attach a colored

Ghost circuit shorts under smt resisters only when they are located on solder side of pcb (glued down)

Electronics Forum | Fri Jul 23 14:07:52 EDT 1999 | Carl J. Odle

We are having a process related problem with pullup resistors on a controller card which has a I960 micro-processor. The controller monitors signal inputs and it's own resources then blinks a LED to indicate its working. The problem is that after a p

  1 2 3 4 5 6 7 8 9 10 Next

located searches for Companies, Equipment, Machines, Suppliers & Information