Electronics Forum: machine and trouble (Page 1 of 159)

Re: MSH Placement trouble

Electronics Forum | Wed Nov 24 13:46:23 EST 1999 | STIMP

HI, I BELIEVE LOOKING TOWARDS MACHANICAL PROBLEMS WANT RESOLVE YOUR PROBLEMS.IT SOUNDS MORE LIKE A SOFTWARE OR MAYBE EVEN YOUR CARD GOING BAD. A MACHINE OF ANY BRAND DOES WHAT YOUR PROGRAM TELLS IT TO.IF YOUR PROGRAM SAYS PULL FROM DEVICE 7 AND YO

MSH Placement trouble

Electronics Forum | Fri Nov 19 07:45:59 EST 1999 | Claude Couture

Our Panasert MSH is randomly mixing up the parts placement. About 1 in 10,000 placement will be a wrong part. The wrong part may be any other part present on the feeder carriage. A chip resistor 0805 may be replaced by a minimelf or a sot-23. It is

tape and reel machine

Electronics Forum | Fri Mar 24 15:20:27 EST 2000 | Chris McDonald

I have recently purchased a Tape and reel machine from V-Tech. We are using Presure Sensitive tape and we are not geting good results. Anything bigger that a SOIC14/16 gives us trouble. The cover tape will pull off on the feeder and we will lose part

Hello, I am having trouble getting the DEK machine to work horizon 03ix software

Electronics Forum | Tue Dec 12 04:49:43 EST 2023 | ttheis

Seems like a file was corrupted on the hard drive. Hopefully you have it backed up. We take a hard drive image of every machine on delivery in case of a hard drive failure or corruption.

Hello, I am having trouble getting the DEK machine to work horizon 03ix software

Electronics Forum | Wed Dec 13 14:33:06 EST 2023 | carl_p

I would start by checking the caps on the PC board. I used to have the same machine & they would fail every few years which could cause some random errors to appear on times.

recently purchased MPM Ap Hie - startup trouble

Electronics Forum | Thu May 01 07:33:19 EDT 2008 | realchunks

Jim, You need to repair or by-pass the cover interlock. The machine thinks it's open and will not procede any further. They all do it, even the new models. Once you get past this warning - you will get the the RESET window - garanteed.

recently purchased MPM Ap Hie - startup trouble

Electronics Forum | Thu May 01 06:35:51 EDT 2008 | kevinjm

Hi Jim, We had a similar problem with an AP-27. You could try to jumper the wires which lead in to the reed switch. Failing that you could swap out the opto module for this, in our machine it's located in rack 2-15. Rgards, Kev.

recently purchased MPM Ap Hie - startup trouble

Electronics Forum | Wed Apr 30 16:00:12 EDT 2008 | tech13108

Hello, We have recently purchased an older MPM via auction and I am trying to get it running but not getting too far. When I power it up it goes thru a boot sequence then a screen appears on the monitor with a "warning cover not closed, close cov

tape and reel machine

Electronics Forum | Wed Oct 10 12:22:08 EDT 2001 | Kevin

Cal, There are several suppliers of cover tape materials that do not require heat to activate the adhesive. 3M and Advantek are likely the leaders. There are relatively few T&R machines that can handle both heat and non-heat applications - as Chri

tape and reel machine

Electronics Forum | Tue Oct 09 22:21:54 EDT 2001 | caldon

.............and since this link originated from march of 2000 I should not expect a response

  1 2 3 4 5 6 7 8 9 10 Next

machine and trouble searches for Companies, Equipment, Machines, Suppliers & Information

SMT feeders

Component Placement 101 Training Course
pressure curing ovens

Software for SMT placement & AOI - Free Download.
SMT feeders

Best Reflow Oven
High Throughput Reflow Oven

Nozzles, Feeders, Spare Parts - Siemens, Fuji, Juki, Yamaha, etc...
Hot selling SMT spare parts and professional SMT machine solutions

Internet marketing services for manufacturing companies