.gif)
Electronics Forum | Thu Oct 20 19:23:18 EDT 2011 | eadthem
As far as the buttons go, White = pause for inspection when depressed, lit when active Green = pass after inspection when lit you need to press the button, when flashing its waiting for the upline machine, Yellow/orange = when flashing indicates
Electronics Forum | Tue Oct 04 20:18:17 EDT 2011 | denmark
Sir *We are using "HOT BAR SOLDERING" we are bonding "FFC" and "PCB" at 0.5mm pitch. Machine settings: Heating Temp. 310º, Colling Temp. 190º Delay Time 1sec We also using "BECKLITE" as Soldering Jig that can resist up to 400º. We are using 1 is to
Electronics Forum | Wed Oct 19 11:33:15 EDT 2011 | caerleon
easier if you recycled on-site? You can still send off for reclaimation the oxide powder that your left at the end of the process. Failing that talk to your supplier to see if they have arrangements to do this for you or look at reducing dross - i f
Electronics Forum | Thu Nov 03 12:59:42 EDT 2011 | davef
We agree Evtimov that the best way to evaluate AOI is to test known good and known bad boards on a machine, preferably in your own plant. Be aware that I can run all of your boards and assure you that there will not a single false call. It's just th
Electronics Forum | Tue Nov 08 07:23:03 EST 2011 | leemeyer
Thanks Bobpan, A function 6 tells me that I have firmware ver IVC 3.05. I keep getting a motor error 4 "The Xand/or Y axis did not reach the commanded position within 500 msec." The battery was dead on this machine so the mod codes were lost. I en
Electronics Forum | Fri Nov 18 08:35:20 EST 2011 | bobpan
try this..... I think there is a coupling for the theta motor....make sure both set screws are tight.....maybe the theta is slipping. Make sure there are no bright lights shining into the machine....maybe even throw a dark cover over the top and try
Electronics Forum | Sun Nov 20 18:15:24 EST 2011 | xborre
Hello, We are about to buy a old used Dima Optimat P&P I have already read the manual to know more about the possibilities. I have read it can place SOT23 packages, but i'm currious if it can recognize and place also the 5 pin variant (SOT23-5) and
Electronics Forum | Wed Nov 23 07:38:49 EST 2011 | davef
We agree with the points made by ScottE above. Additionally, most printers are not heavily loaded. So, you wouldn't have to buy another machine, give-up floor space, purchase and store peculiar tooling, etc. We think Darby does pin transfer. Maybe h
Electronics Forum | Tue Dec 06 19:44:10 EST 2011 | comando
Hello every one! I need help with a misaligned theta at plcc44, the machine is a IP3 smd3, firmware 2.99, vision card 4400 and both camera type YD2048N on label but in Proper data is set 2 (I don't know if this is right) we use Fuji flexa, Back Lig
Electronics Forum | Wed Dec 07 02:35:28 EST 2011 | mk15
Hi, I am looking for help with Error Philips Comet, Start Procedure -OK, INTIAL SERVO ORIGIN -OK, AUTORUNNING -OK, PCB START -OK, FIDUCIAL -OK, PICKUPCOMPONENT -OK, NEXT-ERROR E2 CORRECTION DATA ERROR(CORRECTION DATA IS NOT LOADED OR FAILED TO ADJU
.jpg)
Buyer, Seller, Broker of Electronic Assembly Equipment
Equipment Dealer / Broker / Auctions
309 West Pickle Alley
Rushford, MN USA
Phone: 507-864-7477
