16413 machines results

Electronics Forum: machines (Page 1356 of 1642)

SMT SOT-23 Part Rotation

Electronics Forum | Wed Feb 02 23:28:48 EST 2022 | cbeneat

Something we've run into in the past, not on those machines, a different brand completely, and I have no experience with yours. We were having what you described and what we found was during the part being scanned, there was a bolt that held the shro

Which (cheap / old) pick and place for 0402, 0.5mm FPC small line

Electronics Forum | Wed Feb 23 13:00:48 EST 2022 | stephendo

Every now and then I will be asked if I remember that place I bought that transformer. Often when we get new equipment we will get a new transformer. Not only will you find differences between DEK printers of different names and models, you will fin

Rework Stencils

Electronics Forum | Fri Feb 25 16:54:50 EST 2022 | proceng1

I saw another thread about kapton stencils for rework. I didn't want to hijack that topic, so I am starting a new one. I while back I had the idea to cut KAPTON stencils with a CRICUT machine. I was going to run a test, but I couldn't get a clean

SIPLACE D1i SOT(SMT Transistor lead lift up detection)

Electronics Forum | Tue Mar 01 04:25:48 EST 2022 | shrikant_borkar

Dear Members Please help me to support to one of my client does not have co planarity in his SIPLACE D1i Pick and place machine. We would like to understand why this Lead lift up issue has passed thru pick and place.? Is there any method by keepin

DEK 265 GSX missprint

Electronics Forum | Tue Mar 22 13:00:37 EDT 2022 | bukas

hi, I have a 265GSX machine that prints firs PCB in batch correctly and then missprints the rest(there may be acceptable prints by accident). after hitting END RUN and RUN again, first PCB comes out perfect but others are bad. paste is randomly shift

DEK Horizon Screener

Electronics Forum | Thu Apr 14 14:16:51 EDT 2022 | dsmith

Hello and good morning. I've recently encountered an issue with a DEK tool and no one is able to remedy it. During the initializing phase, the table begins "bouncing" up and down and never stops, halting the process. There's a pass through proximit

BGA REMOVAL WITHOUT TEMPERATURE

Electronics Forum | Thu Apr 14 15:33:41 EDT 2022 | ppcbs

I've never lost memory in a BGA from heat removal. However we can create a profile on our BGA rework stations to remove using bottom heat only. This exposes the BGA body to temperatures of around 190 to 200C. I have a colleague that has a machine

Panasonic CM Nozzle shifts LED's positions

Electronics Forum | Sun Apr 17 00:04:03 EDT 2022 | klauss

I am mounting 3535 Cree High-power leds with p&p machine. First nozzle picks up the led normally and then it's placed good but after 4-5 times nozzle picks up the led like at an angle. looks like it holds the led from the side edge of the dome.

Q on YV88X push-in dial not moving

Electronics Forum | Wed Apr 20 18:06:37 EDT 2022 | kumarb

For future readers - just needed a little bit of lube. Many thanks to Michal & the staff @ Trans-Tec (USA) for their excellent support, as always. Please see attached. For our (dated) machine, the black dial would turn only after hitting the gym

DEK 265 Horizon fiducial drift in the Y

Electronics Forum | Mon May 02 21:26:23 EDT 2022 | rob1

I have a problem with DEK 265 Horizon. During camera being homed after checking the fiducials, the camera failed to home properly and crashed into the back of the machine in the Y direction. I homed the camera in the Y and it appeared OK and I could

1356