Electronics Forum: motherboards daugther boards (Page 1 of 6)

Samsung CP40 mother board substitution

Electronics Forum | Sun Sep 23 19:05:04 EDT 2007 | darby

Floyd, Purchase a spare set of motherboards, get the numbers from the boards and google them up. The CP-40 motherboard is getting on now so you should pick up new ones very cheap. Also don't forget to check the battery on the motherboard.

Aquastorm Motherboard question

Electronics Forum | Fri Jan 23 13:14:36 EST 2009 | gregcr

Hi All, I have an aquastorm 100 that I need to upgrade the motherboard in. If anyone has one of these machines could you take a look and see what the MFG & MFG part number of the mother board is. The new board has a FLASH memory drive rather than

MPM AP27 motherboard

Electronics Forum | Tue Apr 08 08:57:04 EDT 2008 | toddl

We had a similar issue with a UP2000. We had motherboard problems and needed a new one. Our original board had a 33Mhz CPU but none were available, Speedline told us we needed to buy the upgrade. One of their techs told me that they had a 66Mhz mothe

Heller 1809EXL TDM repair

Electronics Forum | Wed Jun 24 06:18:59 EDT 2020 | bukas

there is a oven setup wizard, I think you should be able to adjust probe offsets there. are the probes original? maybe they are replaced with inadequate ones? also, contacts on TDMs are weak, give them a good clean if you havent already. if you get "

BGA rework

Electronics Forum | Tue Mar 20 03:21:32 EST 2001 | hany_khoga

Dear Mr. Stephen: After all boards we lost & hard time we had, the only convencing solution for us is to run a good pc_motherboard (which is our product)to confirm the experiment. After that we need to remove the big BGA ,clean & flux the PCB then s

DEK 265 motor com error, axis 1,2,3 fatal error

Electronics Forum | Wed Aug 31 08:12:37 EDT 2016 | ttheis

Search for the bios or motherboard on ebay. Type in the part numbers you find on the boards and see if anything comes up. Often these are standard pc boards. I've repaired my old MPM by finding the cards on ebay cheap.

BGA Reflow profiles

Electronics Forum | Wed May 20 00:02:08 EDT 2009 | microdot

yes you are correct that we are repairing motherboards. We are not reflowing the entire board to replace one component. We are using reflow machine to reflow the particular component.

Motherboard become NO POST when humidity increase to 90%

Electronics Forum | Wed Nov 25 09:40:56 EST 2009 | Sean

Hi Greg, The board is with immersion silver finishing..One of my friend had the same issue even with PCB OSP finishing.. Besides, no white residue found on the top side... Its only appear on the bottom side but no so obvious... Rgds, Sean

Lower Temperature Processing- Solder Paste

Electronics Forum | Thu Feb 09 04:28:05 EST 2017 | soldertraining

Solder Pastes are used particularly in the assembly of printed circuit boards (PCBs) for a wide variety of applications, including hand-held electronic devices such as smart phones and tablets, computer motherboards, consumer electronic products, net

Hanwha Samsung SM320 Failed to Start Mark5 SW - VME broken ?

Electronics Forum | Sat Mar 11 22:07:35 EST 2023 | recard

Hi Duro. The problem is that my VME card and ISA card was tested in another machine and both are working. So I suspect the CAN boards or Motherboard.

  1 2 3 4 5 6 Next

motherboards daugther boards searches for Companies, Equipment, Machines, Suppliers & Information

Thermal Interface Material Dispensing

Have you found a solution to REDUCE DISPENSE REWORK? Your answer is here.
High Throughput Reflow Oven

Want to know where to find the best AOI system? - Read testimonials.
MSD Dry Cabinets

High Precision Fluid Dispensers
one-stop for smt solution

Training online, at your facility, or at one of our worldwide training centers"