Electronics Forum: mpm camera error (Page 1 of 32)

MPM Accuflex error camera vision

Electronics Forum | Fri Mar 05 12:24:34 EST 2021 | astarotf

Hello Our problem was the camera that was bad, we replaced it and it worked again, greetings!

MPM Accuflex error camera vision

Electronics Forum | Thu Mar 04 22:38:54 EST 2021 | tomek_k

Hi Miałem taki problem, myślałem też że to uszkodzona karta Cognex. Zakupiłem nową i to nie pomogło. Okazało się że trzeba zainstalować właściwy sterownik karty. (translate from PL) regards Tomek

MPM Accuflex error camera vision

Electronics Forum | Mon Feb 10 08:18:18 EST 2020 | astarotf

Hi We have an Accuflex MPM with camera vision problems which shows no image, only the screen looks gray. With the diagram we show that our MPM camera is receiving the appropriate 12V voltage on pin # 6 of the camera and supplies the video output on p

mpm up 2000 camera problem

Electronics Forum | Tue Aug 15 02:45:14 EDT 2006 | dman97

Does anyone know if it is possible to lower the camera brightness when selecting fiducials? Our UP2020's camera is extremely bright and sometimes it causes the fiducials to be rejected cause they are too bright to be seen. Any settings than can be a

mpm up 2000 camera problem

Electronics Forum | Tue Aug 15 10:55:23 EDT 2006 | chrisgriffin

Some software versions won't allow a brightness change with the next button. You should do a histogram test. Place a board on the worknest, then a smooth white card on top of that. Then jog the camera over the card. Raise the Z-axis to it's softwa

mpm up 2000 camera problem

Electronics Forum | Tue Aug 15 12:02:55 EDT 2006 | pr

Check your gel flex. They're no good. Don't use em. good Luck pr

mpm up 2000 camera problem

Electronics Forum | Tue Aug 15 09:40:43 EDT 2006 | SWAG

Not sure about 2020 but AP's have an option to perform a histogram test/adjustment on the lighting. It's a black card, white card test and you can adjust a pot. in the machine to make the histogram curve "best-fit". On an AP, you find this option i

mpm up 2000 camera problem

Electronics Forum | Tue Aug 15 07:31:27 EDT 2006 | Chunks

Yes, when teaching fids and you get to the screen shows your fid (either board or stencil), hit the middle "roller button" labeled NEXT. This will toggle your bulb from regular to bright and vice/versa. If it's still very bright, the bulb itself ma

Camera not parked error on mpm ap 25.

Electronics Forum | Mon Jun 12 10:38:00 EDT 2017 | highmillr

Getting this error more frequently. Whats causing this?? I have to reset machine every time costing man hours. After resetting its fine but does it at least once a day.

Camera not parked error on mpm ap 25.

Electronics Forum | Mon Jun 12 23:52:58 EDT 2017 | aemery

Don, either you have a faulty park sensor or much more likely the vision gantry Y axis is not reaching the sensor. Possible issues, one of the two VY drivers cards is failing; one of the VY forcer motors (air bearings) is failing; to much air leakin

  1 2 3 4 5 6 7 8 9 10 Next

mpm camera error searches for Companies, Equipment, Machines, Suppliers & Information

Benchtop Fluid Dispenser

World's Best Reflow Oven Customizable for Unique Applications
pcb precision cleaning

MSD Dry Cabinets
SMT feeders

Have you found a solution to REDUCE DISPENSE REWORK? Your answer is here.


Private label coffee for your company - your logo & message on each bag!