Electronics Forum: mpm momentum

MPM Up2000 and SMEMA

Electronics Forum | Tue Sep 13 02:31:50 EDT 2016 | bukas

board input sensor sensitivity? maybe conveyor movement triggers it and because of that it sends pulse. conveyor moves few millimeters, how does machine act?

MPM UP3000 Question

Electronics Forum | Fri Aug 11 11:18:20 EDT 2006 | chrisgriffin

I got a 3000 that is acting crazy. After a print, the board is unclamped and the Z-axis lowers. It continues to lower until it trips the limit switch. It is suppposed to move in the Y-axis to line up with the tracks while lowering in the Z-axis.

MPM Up2000 and SMEMA

Electronics Forum | Thu Sep 15 06:45:26 EDT 2016 | awhite

Hi Ariss_T, Thanks! I actually did check that...that was one of my first thoughts as well. While in the I/O, I slide a raw board back and forth under the camera/sensor and it acted appropriately. I will definitely update this thread as new informa

screen printer - vision

Electronics Forum | Mon Apr 26 08:15:37 EDT 2004 | pjc

MPM uses a one-print-Mylar system, as do other printer mfrs. In this system there is a Mylar sheet attached to a frame that is secured over the printer table with the board on it. You print onto the Mylar. The table X-Y-theta manual adjustments are u

MPM AP25Hie Pre Board Stop error

Electronics Forum | Mon Jul 30 17:32:34 EDT 2007 | chrisgriffin

When you teach the "teach boardstop Y" make sure the camera is seeing the leading edge of the board and not too close to the rails. It should calculate the pre-stop position correctly. I assume you have thoroughly checked the sensor. Also check th

MPM Accuflex fails to initialize powered rail

Electronics Forum | Mon Jul 21 11:01:11 EDT 2014 | dontfeedphils

I dealt with the same issue for a month or so. We jumped through a lot of hoops, replaced both lead screws, verified the motor was good, a ton of stuff. Ended up being an intermittent wire connection between the control board and the conveyor width

MPM UP500 blowing power supplies

Electronics Forum | Wed Nov 30 20:43:06 EST 2016 | ttheis

OK, so went to power up again today and had the same kind of issues. The 24V and 5V lights on the cage flicker dimly about every 500ms. I tried my trick of disconnecting the +24v lead to the lift table amp and it acted the same, so it didn't work th

MPM Up2000 and SMEMA

Electronics Forum | Tue Sep 20 15:00:26 EDT 2016 | awhite

Got it!!!!! On the main Operator Screen for the MPM UP2000, and under configuration (when logged-in under maintenance), it gives you ONLY the settings that the machine is set to....there are no drop-downs or options available to choose from. Very fr

solder paste

Electronics Forum | Wed Jul 27 09:58:05 EDT 2011 | davef

Pressure printing systems Conventional stencil printing techniques have fundamental limitations as regards paste handling: The volume of paste available for printing is limited, so frequent replenishment is necessary Paste is difficult to c

Re: I'm baaack!

Electronics Forum | Wed Apr 21 13:52:34 EDT 1999 | Steve Gregory

Technically speaking, there is nothing for me to say. Oh maybe just one thing - to get me back into the fray: Steve, I must say I totally disagree with your assessment of under screen cleaners. I have had nothing but excellent results using the dry,

  1 2 Next

mpm momentum, accuflex, mpm act searches for Companies, Equipment, Machines, Suppliers & Information

PCB Handling with CE

Training online, at your facility, or at one of our worldwide training centers"
Electronics Equipment Consignment

High Precision Fluid Dispensers
PCB Handling Machine with CE

Best Reflow Oven