Electronics Forum: mpm up 2000 fiducial light (Page 1 of 2)

mpm up 2000 camera problem

Electronics Forum | Tue Aug 15 02:45:14 EDT 2006 | dman97

Does anyone know if it is possible to lower the camera brightness when selecting fiducials? Our UP2020's camera is extremely bright and sometimes it causes the fiducials to be rejected cause they are too bright to be seen. Any settings than can be a

mpm up 2000 camera problem

Electronics Forum | Tue Aug 15 09:40:43 EDT 2006 | SWAG

Not sure about 2020 but AP's have an option to perform a histogram test/adjustment on the lighting. It's a black card, white card test and you can adjust a pot. in the machine to make the histogram curve "best-fit". On an AP, you find this option i

Stencil Fiducials

Electronics Forum | Thu Feb 15 12:34:11 EST 2007 | flipit

Does Ekra or MPM require stencil fiducials be filled with Black Max or some other black epoxy? We still require our stencil supplier to do this. I did not have to do this on any Dek solder printers since 1997. Can the MPM UP2000 HiE fiducial light

Mpm "Camera not parked" Error

Electronics Forum | Thu Dec 01 16:11:03 EST 2011 | cowens

I have a MPM UP2000. When running or after teaching fiducials you will here a clank and the error "Camera not parked" will show. If anyone has experienced this on have any suggestions plaese advise. Thank you.

MPM UP2000 Installation

Electronics Forum | Thu Mar 30 07:44:19 EST 2006 | Chunks

UP 2000 is a good printer. Spares are normal - blades, stencil/board light bulbs, the over head flourecent, get new conveyor belts. Take the cover off the tactile sensor and make sure it's clean also. Other than that it should be a work horse.

MPM Accuflex questions and issues

Electronics Forum | Thu Feb 15 13:46:16 EST 2018 | aemery

Griinder, Maybe it's me, but I think what you might be saying here is that you see a reflected image of the PCB or Stencil when you and teaching the fiducials and it is interfering with the teaching routine, is that correct? If this is true it is c

MPM Accuflex, Lost Vision

Electronics Forum | Thu Aug 13 14:52:42 EDT 2015 | deanott

We just encountered a problem with the vision on our MPM Accuflex. We just switched jobs and when we went through a 'Vision Set-up' there was no image (just blank gray screen where you'd normally see the PCB or bottom of stencil). When we tried to

MPM UP2000 problem

Electronics Forum | Thu May 09 01:43:56 EDT 2019 | compit

in my camera did not detect PCBs from light green laminate - did you try on a different color PCB?

MPM UP2000

Electronics Forum | Wed Sep 30 06:22:23 EDT 2015 | mervin

MPMENG, Thank you so much for taking the time to help. The machine has Y snuggers and flippers. The Pcb is loading in the center all the time. The driver cards look fine there is no obvious faults on them or partially burned. The machine was not in

MPM UP2000

Electronics Forum | Tue Sep 29 10:10:34 EDT 2015 | swag

We used to have a UP3000. Long time ago so I'm rusty but isn't there a setting for fid correction that you an program to occur after each board or after 5, 10, etc.? I thought I remembered doing offsets on ours as the camera was a little wacky (old

  1 2 Next

mpm up 2000 fiducial light searches for Companies, Equipment, Machines, Suppliers & Information

PCB Handling with CE

IPC Certification Training from the comfort of your home or office
Global manufacturing solutions provider

High Throughput Reflow Oven
Selective soldering solutions with Jade soldering machine

Training online, at your facility, or at one of our worldwide training centers"