Electronics Forum: mpm up2000 board model not found (Page 1 of 2)

mpm up2000 cmos battery low fix needed

Electronics Forum | Fri Apr 05 01:23:29 EDT 2024 | ddfreeze

thank you so much for the info, wished I would have known previously, however I found the motherboard manual online, and located the Dallas CMOS chip soldered to the board. Found a lot of youtube fixes online. Dremel tool and some soldering, added an

MPM Up2000 and SMEMA

Electronics Forum | Wed Sep 14 23:30:30 EDT 2016 | ariss_t

Hi, my 2cent.. u could try to check the sensibility of the camera board stop sensor.. maybe it detect something i.e support block.. do reply when u found the actual root cause.. thanks..

MPM UP2000 Hi-e

Electronics Forum | Thu Sep 07 09:04:24 EDT 2006 | Doug Eidle

Hi, First off, I am the Pre Owned Equip. Business Mgr. for Speedline Technologies. We have a factory Renewed (our enhanced refurbishment process) available. You can contact your local Speedline MPM Rep for price and information. If board warp is

MPM UP 2000 conveyor misalignment

Electronics Forum | Wed Sep 26 07:40:30 EDT 2012 | highmillr

I had this problem at another plant with the UP 2000....When the machine resets, The left and right side of the conveyor misaligns, causing the conveyor to be tight on the loading end and boards falling out of the unloading end. or vise versa...the t

DEK ELA and MPM U2000 Hi-E Comparison

Electronics Forum | Mon Jul 29 09:19:00 EDT 2002 | pjc

Quick Change Tooling is one advantage for DEK when comparing the MPM UP2000. DEK has Form Flex. Good system, but I've heard concerns about long term dependabilty. All support tooling options offered on the UP2000 takes a bit of time to set up. So, If

MPM UP2000 HiE Z problem

Electronics Forum | Fri Aug 07 09:53:12 EDT 2009 | kpm135

The Z-axis Drive card on our MPM UP2000 HiE fried. We replaced it with a new card, setting all the jumpers to match the old card. After that we had to recalibrate the Z-axis and the snugger height but the problem is that the camera is now too close t

MPM Up2000 and SMEMA

Electronics Forum | Thu Sep 15 06:45:26 EDT 2016 | awhite

Hi Ariss_T, Thanks! I actually did check that...that was one of my first thoughts as well. While in the I/O, I slide a raw board back and forth under the camera/sensor and it acted appropriately. I will definitely update this thread as new informa

MPM UP2000

Electronics Forum | Wed Sep 30 06:22:23 EDT 2015 | mervin

MPMENG, Thank you so much for taking the time to help. The machine has Y snuggers and flippers. The Pcb is loading in the center all the time. The driver cards look fine there is no obvious faults on them or partially burned. The machine was not in

MPM Teaching Vision

Electronics Forum | Wed Jun 02 19:03:11 EDT 2004 | black5629

My board is in the center, it appears that it would read the stencil but not the board. " Board Model NOT found".I am open for any input.

MPM Teaching Vision

Electronics Forum | Tue Jun 01 17:55:30 EDT 2004 | black5629

I am new with MPM printer,need help.I am trying to teach a new board, after selecting targets,when I exit teach vision ,it errors out "Board Model Not Found". Board orientation is correct. The books talks about Vision Y not squared to axis. Does anyo

  1 2 Next

mpm up2000 board model not found searches for Companies, Equipment, Machines, Suppliers & Information

PCB Handling Machine with CE

Training online, at your facility, or at one of our worldwide training centers"
IPC Training & Certification - Blackfox

Nozzles, Feeders, Spare Parts - Siemens, Fuji, Juki, Yamaha, etc...
Voidless Reflow Soldering

Component Placement 101 Training Course
SMT feeders

Software for SMT placement & AOI - Free Download.