Electronics Forum: my12 issues (Page 1 of 3)

my12 motor amplifier channel a error

Electronics Forum | Wed Jan 29 18:41:22 EST 2014 | alphatronique

Hi did you look for mechanical issue like friction somewhere ? when init i use very low force buy much more while running that may explain wly machine work in production fur fail only on init i face that whit flex cable that make just little fr

my12 motor amplifier channel a error

Electronics Forum | Fri Jan 10 11:32:52 EST 2014 | rgduval

Hi, Hans, I would have suggested swapping the MOT card out to see if that fixes the issue (or, changing the MOT card with another one to isolate the card), but, it sounds like you've already done that. I'm surprised that MyData would point you towa

MY12 Dual Vision Camera Calibration issues

Electronics Forum | Mon Mar 21 17:59:08 EDT 2022 | guyt

Thanks for the idea, we will give it a go. Cheers for now g

MY12 Dual Vision Camera Calibration issues

Electronics Forum | Tue Mar 15 17:47:24 EDT 2022 | guyt

Hi, Has anyone had a issue with a MyData my12 dual camera system, were the calibration always shifts up after a few hours of use. It's not the mechanical calibration. it is like the machine loses it's software calibration co-ordinates ?? Any ideas

MY12 Dual Vision Camera Calibration issues

Electronics Forum | Thu Mar 17 18:20:17 EDT 2022 | SMTA-64387687

It sounds like a mechanical issue. Otherwise, you'd lose other calibration. Try backing up the parameters. Then, when the camera is out of calibration, restore the parameter and see if that fixes the problem.

MY12 HYDRA issu

Electronics Forum | Thu Dec 22 15:11:40 EST 2022 | jbrochecouste

hello, I am looking for information on the following error message: F-MOT-MSETDYN HYDRA Z/156 / TIMEOUT... on a MY12, tell me your experience until the problem is solved

MY12 HYDRA issu

Electronics Forum | Mon Dec 26 18:02:37 EST 2022 | rgduval

So, your Hydra Z message timed out... A couple of potential causes: 1. Hydra MOT card failure 2. Hydra z-motor failure 3. Hydra z-motor encoder failure 4. Hydra z-lock failure 5. Disconnected cable 6. X-wagon cable Start by booting into service mod

MY19 Midas Tool Issue

Electronics Forum | Thu Sep 08 18:10:09 EDT 2022 | mt396596

We just went through a similar issue with our MY12E. Make sure your Midas vacuum system is working, check your Midas Z friction. Also verify the Centering unit centering band. You can swap your MOTZ and MOTC to rule out the card. The tool install t


Electronics Forum | Mon Aug 05 09:39:07 EDT 2019 | filipblad

Hi, I'm getting the F-MOT-MOVE X/156 error on our MY12 pick'n place. The manual tells me its an hardware issue. I found another thread on here where someone had a similar issue and they found out it was a power subbly issue. If I open the service pro

MY12 tpsys keeps rebooting

Electronics Forum | Tue Apr 25 00:01:40 EDT 2017 | tomwd

Hi everyone, I am new to My12 pick and place. I have MY12 machine shutdown during run. Since then when I power up the machine, the TPSYS keeps rebooting, and never completing Initiate Hardware phase. I suspect that it is a hardware issue rather than

  1 2 3 Next

my12 issues searches for Companies, Equipment, Machines, Suppliers & Information

Software for SMT

High Throughput Reflow Oven
One stop service for all SMT and PCB needs

Training online, at your facility, or at one of our worldwide training centers"
convection smt reflow ovens

Want to know where to find the best AOI system? - Read testimonials.