Electronics Forum: my12 y (Page 1 of 2)

my12 motor amplifier channel a error

Electronics Forum | Wed Jan 29 13:01:04 EST 2014 | tech1

Back when the Linear Y wagons first came out Mydata had problem with the original Y amplifier and were swapping out the complete box for customers who had problems. There was also a problem with the encoder that resulted in the same type of errors yo

my12 motor amplifier channel a error

Electronics Forum | Fri Jan 10 03:33:42 EST 2014 | hans88

hello people, we have a my12 wich has a problem it gives the following error during hardware initialization: F-MOT-MSETDYN Y/1236 :Motor amplifier channel a error. after this error it says hardware initialization failed. this prevents us of using

How do I calibrate the Position camera on the x wagon

Electronics Forum | Tue Jul 14 13:20:13 EDT 2020 | tomdegas

I have a MY12 running TPS 2.8.1 and I need to know how to calibrate the X wagon Visin system. The machine is off in the Y direction after I removed and replaced the camera.

MY12 F-MOT-MSETDYN x/12: Position Counter Dead

Electronics Forum | Fri Sep 05 09:22:53 EDT 2014 | rgduval

Hi, Rebecca, Hmm...two x motors? I'm a couple of years removed from MyData's, but, I don't remember two x-motors. Might be something in the My12's that I didn't see in my older My9 (and certainly not in my TP9). As to the small board...unfortun

F-MOT-MSETDYN Theta/12: No axis movement detected by transducer

Electronics Forum | Thu Feb 06 20:23:35 EST 2020 | bilalfarooqi

Hey everyone, We use a MyData MY12 machine and we are experiencing a problem with the Midas head. I recently replaced a torn vacuum tube that goes on the zfib card. The machine worked perfectly for a day and a half but now MY12 has completely stoppe

Mydata Lift motor 2 amplifier error

Electronics Forum | Thu Oct 15 10:21:30 EDT 2015 | azdback

troubleshooting a table lift error on MY12. Error code: F-MOT_Releaseboard conveyor lift/1304. Basically, the table got stuck on the up position. Also bench tested both lift motors and they are ok.Rotated the lift motors manually to test the encoder

MY19 Midas Tool Issue

Electronics Forum | Thu Sep 08 18:10:09 EDT 2022 | mt396596

We just went through a similar issue with our MY12E. Make sure your Midas vacuum system is working, check your Midas Z friction. Also verify the Centering unit centering band. You can swap your MOTZ and MOTC to rule out the card. The tool install t

Samsung SM320 vs Mydata MY12E

Electronics Forum | Thu Mar 22 09:49:16 EDT 2007 | Manyhatz

You shouldn't have any problem with the SM320 doing what you're asking above. In fact I think it will do it quite better. We have a two machine TP-11 Hydra line and a two machine SM320 line and I can tell you one SM320 can get the job done better.

Mydata M12 issue

Electronics Forum | Tue Oct 27 11:20:16 EDT 2009 | smtspecialist

I had the same problem back in March with my MY12, since I have two identical lines i swapped things around until swapping the x-wagon motor (the one for fine movements). When I swapped the x-motor I move the problem from one line to the other gener

F-MOT-MSETDYN Theta/12: No axis movement detected by transducer

Electronics Forum | Fri Feb 14 16:01:28 EST 2020 | bk

On the my12 the panel on the front of the machine comes off two screws each corner to loosen the panel. There is a pull out tray that gives you easier access to the computer, ps3, etc. It will be the box in the center on top it should label where eac

  1 2 Next

my12 y searches for Companies, Equipment, Machines, Suppliers & Information

Circuit Board, PCB Assembly & electronics manufacturing service provider

Smt Feeder repair service centers in Europe, North, South America
Win Source Online Electronic parts

Stencil Printing 101 Training Course
PCB Handling with CE

Wave Soldering 101 Training Course
Encapsulation Dispensing, Dam and Fill, Glob Top, CSOB

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.