Electronics Forum: my2

Technical problem with MPM-AP-24

Electronics Forum | Thu Nov 11 17:49:11 EST 2004 | pdeuel

We are having a problem with our AP-24x printer. When the vacuum motor spins up we get a 60 hz buzz into the DC drivers for the forcers and the stencle wiper. We also indicate a main power drop from 115 vac to 80 vac. The vacuum motor checks out good

Relay Coil Impedence

Electronics Forum | Thu Mar 01 23:15:28 EST 2007 | jmelson

You shouldn't be worrying about "impedance" on a DC relay. Just measure the resistance with a Voltmeter/Ohmmeter. If you need to know the current draw, it will be 24/resistance The impedance of an AC relay changes as the armature moves from the "off

cp65 Thermal Alarm

Electronics Forum | Fri Jan 03 15:10:49 EST 2014 | jimmyboz

SET-MANUAL-IO Thermal alarm can be an overload relay, vacuum pump for nozzles or scrap vacuum. It may also be overtemp from the cam box "oil" temp. The 2 overload relays have reset buttons, press and try to feel for a "click". If it is directly t

Philips Topaz - conveyor motor doesn't work

Electronics Forum | Tue Sep 01 01:05:24 EDT 2015 | rgarcia0626

I'm not familiar with you machine but it seems the problem is not the motor. if there's a manual I/O, switch on your conveyor from there and check if there's a voltage going into the motor.Check the control boards for the conveyor, relays and sensors

automatic placement of pin through hole component

Electronics Forum | Wed Feb 09 08:54:42 EST 2000 | pascal MATHIEU

Hello friends , in order to try to reduce our labour cost , we are thinking to replace manual placementof PTH COMPONENTS by automatic unit which 'll be able to place relays ,and connectors . is there anybody on this forum to advise us on this topi

Heat guns and component damage

Electronics Forum | Tue Jan 31 15:40:44 EST 2006 | mgdrouin1

Comp is relay. I've pulled the spec. Max 240. Using Leister h/g with manual temp settings from 1-6 (20 - 600C)set by the operator. Gun was set to setting 4. They are using the heat gun to reflow the solder after SMT but before wave. High fai

MPA III Power source

Electronics Forum | Wed Jan 21 06:27:15 EST 2009 | gidster

Seem to be having difficulty with a MPA power source,it powers itself down every now and then. I have changed the relays nc4d and nc2d seems to work for a while but then it rears it's ugly head again, has anybody got any ideas or schematics as the ma

HP 3065 in circuit tester

Electronics Forum | Thu Apr 09 22:50:50 EDT 1998 | Larry

Configuration of our HP 3065 in-circuit tester: HP3065 HL testhead with CL+ controller with 2 hard drives and tape drive 11 Hybrid cards 4 Analog cards 1 GP relay card 2 DUT power supplies (6038A) 1 HP color terminal (2397A) 2 HP terminals (700/92 an

Re: HP 3065 in circuit tester

Electronics Forum | Mon Apr 20 10:20:37 EDT 1998 | Joyce Hughes

Configuration of our HP 3065 in-circuit tester: HP3065 HL testhead with CL+ controller with 2 hard drives and tape drive 11 Hybrid cards 4 Analog cards 1 GP relay card 2 DUT power supplies (6038A) 1 HP color terminal (2397A) 2 HP t

Reflow PBGA

Electronics Forum | Fri Jun 28 03:04:21 EDT 2002 | Dreamsniper

Forgot to include the following: Dwell time is from 55 secs to 68 secs. Indium specs for the paste is maximum peak @ 228'C and 30 to 90 secs dwell time above 183'C. PCB is a 6 layer board with Dimension of 205 x 166 mm but is slightly dense with 11

  1 2 Next

my2,dc24v relay manual searches for Companies, Equipment, Machines, Suppliers & Information

Jet Printing and Cleaning Challenges

MSD Dry Cabinets
Jet Printing and Cleaning Challenges

Have you found a solution to REDUCE DISPENSE REWORK? Your answer is here.
In-line PCBA Routing Machine Shenzhen ETA

World's Best Reflow Oven Customizable for Unique Applications
SMT spare parts - Qinyi Electronics

Stencil Printing 101 Training Course
Cable Assembly and Wire Harness Manufacturing Flux Connectivity

MIRTEC - the Global Leader in PCB INSPECTION Technology.