Electronics Forum: mydata error (Page 6 of 19)

Mydata Hydra tool reference mark error

Electronics Forum | Sat May 04 14:36:53 EDT 2013 | dontfeedphils

It's been a while since I've used a MyData but I believe what happens is on the bottom of the hydra black metal piece is a mark that the vision system uses to locate the tools as they pass over to center the parts. Something may have happened to this

Mydata Hydra tool reference mark error

Electronics Forum | Wed May 08 11:20:24 EDT 2013 | amelby

Thanks for the info on the Hydra tubes that will be helpful. I found the answer from one of the Mydata techs. The Camera needs the hydra head to go slower then 1.9m/sec and the setting was at 1.8m/sec. They found out that even if the machine was set

Mydata Hydra tool reference mark error

Electronics Forum | Mon May 06 11:16:07 EDT 2013 | rdubya

if you don't have anything obstructing the camera then it sounds like it could be the camera power supply going bad. what version of tpsys are you running?

MYDATA HYDRA Z/156 error on Hardware Intialization.

Electronics Forum | Mon Apr 06 14:02:05 EDT 2020 | tomdegas

I have tried that Tim and I get the same error message. Originally it would pass in the service menu but when I switched back to TPsys, it would fail. I tested the friction one time it did pass and it was well withing the range. Thanks for the res

MYDATA HYDRA Z/156 error on Hardware Intialization.

Electronics Forum | Fri Mar 06 14:33:53 EST 2020 | bk

Another thing you can check is where the bar comes down off of the hydra z motor there is a little bearing you can see from the front make sure that bearing is turning even oil it up a little. You can also adjust the tension by loosening the tiny set

MYDATA HYDRA Z/156 error on Hardware Intialization.

Electronics Forum | Fri Mar 06 19:32:09 EST 2020 | SMTA-Alex

The fact, that your Hydra head goes up and then starts moving slowly, means that it didn't find the limit. Since there are no mechanical obstructions and you swapped all the boards, the things to look at are cabling. Double check the ribbon cables fo

MYDATA HYDRA Z/156 error on Hardware Intialization.

Electronics Forum | Mon Apr 06 17:08:30 EDT 2020 | tima

Try swapping XWB board that is on top of X-Wagon. Have you try that? All signals go thru there. Another thing can be those 2 ribbon cables that are behind of X-Wagon. How long ago did you change them? What I would do is to move X to different positio

Mydata Hydra tool reference mark error

Electronics Forum | Sat May 04 11:24:08 EDT 2013 | amelby

Hi, I have been having a problem with my My19E's hydra. The machine comes up with an error "Failed to locate HYDRA tool reference marks" and stops running. It does not happen for about the first two hours of running. It starts to happen after that an

MYDATA TP11 - Motor Controller M error

Electronics Forum | Fri Jun 03 15:19:19 EDT 2011 | jeremymc

After reseating the M controller boards I was able to get further than I had previously, no save status error, and was given an error about the voltage being wrong. During my last run my company had an electrician in to rewire somethings and put a

MYDATA TP11 - Motor Controller M error

Electronics Forum | Fri Jun 03 14:21:48 EDT 2011 | rgduval

I haven't seen that particular fail....but... What was the failure with the M controller? Might try moving your MOT cards around, to see if the failure follows one particular card. If so, you'll know you need a new MOT card. That might satisfy th


mydata error searches for Companies, Equipment, Machines, Suppliers & Information