Electronics Forum: mydata hydra amplilfier a error (Page 1 of 4)

Z force sensor error mydata 11

Electronics Forum | Mon Feb 17 18:53:34 EST 2020 | richgreen01

Hi all I am experiencing z force sensor errors on a couple of different nozzles ( not hydra ) any help appreciated.

MyData F-MOT MOVESLOWMOVE HYDRA error

Electronics Forum | Thu Mar 28 14:28:26 EDT 2024 | kingkelvin

We have MY9 - when it changes hydra tooltips - most of the time it makes a small "hitting" type noise - with error F-MOT MOVESLOWMOVE HYDRA Z/205 - however you can just hit continue and it will always change the tools and finish the board - I've un-i

MyData F-MOT MOVESLOWMOVE HYDRA error

Electronics Forum | Mon Apr 08 14:07:25 EDT 2024 | kingkelvin

Hello all - so I got in the calibrate plate for hydra tool offsets - it completed the calibration - I then installed the first row of white tips with the menu - and the machine still does same thing it puts the tips away but makes a hitting type nois

MyData F-MOT MOVESLOWMOVE HYDRA error

Electronics Forum | Thu Mar 28 18:00:31 EDT 2024 | alexv

The tapping noise is what you hear when Hydra taps each tool on the tool bank to make sure the tips are seated well. The error is a Z-motor problem. The gear is at the top of the Hydra and needs grease. Have you cleaned the old grease and applied new

Mydata MY12 Hydra Theta error

Electronics Forum | Thu Nov 24 16:53:03 EST 2011 | dontfeedphils

Oh wow, I suppose that would fix it huh? That's too bad that the whole unit had to be replaced, but look on the bright side, you should have a decent amount of spare hydra parts now right? haha

Mydata MY12 Hydra Theta error

Electronics Forum | Tue Nov 15 23:03:07 EST 2011 | supse

Hi I have a problem with one of our MY12 machines, the machine stops very often (approx. 10-20 times a day) writing the following error message : f-mot-msetdyn hydra theta/205(f-hrdw-3). We then have to reinitialize the machine to continue productio

Mydata MY12 Hydra Theta error

Electronics Forum | Mon Nov 21 21:46:49 EST 2011 | supse

Thanks Phil But the belt and spring has been changed recently. Unfortunatly we couldn't wait any longer for a solution, so we had to go for a change of the hydra-unit. This seems to have solved the matter, but I had hoped for a less expensive solutio

MyData F-MOT MOVESLOWMOVE HYDRA error

Electronics Forum | Thu Mar 28 17:00:32 EDT 2024 | kingkelvin

For the hydra camera z-level - there is short section in manual - mentions using metal ruler to cover the camera - but for the other cal steps - I see nothing in the manuals for instructions - so I don't know if any special jigs are needed? I don't h

MyData F-MOT MOVESLOWMOVE HYDRA error

Electronics Forum | Tue Apr 02 14:56:30 EDT 2024 | kingkelvin

Hi all - my problem is a bit worse now - I can get all hydra tests to pass in extended service, except indicator levels at current 7 a bit high past 190 limit at ~210-220 - other than that hydra bank re-installs OK - but still it makes a bad hitting

Mydata MY12 Hydra Theta error

Electronics Forum | Wed Nov 16 18:20:39 EST 2011 | dontfeedphils

According to the message guide it just says that it's a error telling you to initiate the Hydra Theta axis. I suppose the encoder for the hydra theta motor could be losing count and causing it to need to be re-initiated, or it could be something to

  1 2 3 4 Next

mydata hydra amplilfier a error searches for Companies, Equipment, Machines, Suppliers & Information

Best SMT Reflow Oven

High Throughput Reflow Oven
See Your 2024 IPC Certification Training Schedule for Eptac

Best Reflow Oven
Win Source Online Electronic parts

Stencil Printing 101 Training Course