Electronics Forum: mydata lower end point not repeatable (Page 1 of 1)

Mydata theta problem

Electronics Forum | Wed Sep 16 14:04:33 EDT 2015 | adventurelights

Hi guys, Recently got an error message when initiating hardware on a Mydata TP9-UFP. Message is: Theta/2: Lower end point not repeatable. Reinitiating fails at message. Haven't seen this message before. Any idea what it could be as production is hal

Mydata theta problem

Electronics Forum | Sat Sep 26 00:53:54 EDT 2015 | padawanlinuxero

Hi guys, > > Recently got an error message when > initiating hardware on a Mydata TP9-UFP. Message > is: Theta/2: Lower end point not repeatable. > Reinitiating fails at message. Haven't seen this > message before. Any idea what it could be as

Mydata TP11 1995

Electronics Forum | Tue Apr 05 05:19:30 EDT 2005 | blueflag

Breakdown help machine will not 0 set upper end point limits on Z axis Theta / lower end point missed Thanks Colin

large bga (55mmx44mm) capable placement machines?

Electronics Forum | Wed Sep 08 15:59:25 EDT 2004 | kbayram

Hello, I'm looking for a lower end used machine that can place a 55x44mm sized bga component, placement speed is n't concern. At the moment I have only found the quad ivc to be capable although I'm worried about the placement accuracy and repeatabi

CSM 84VZ Programming Question

Electronics Forum | Tue Mar 19 09:17:16 EDT 2013 | rgduval

Any CSM84 geniuses out there? I've been working on these machines for about six months now, after spending 10 years on MyData's. I'm adjusting to the way the CSM's see the world, but, have run into something that I could use an assist with. I'm ha

MyData Missing Placements

Electronics Forum | Thu Jun 28 20:11:32 EDT 2007 | rfrog

Hi folks, I've been bouncing off of MyData technical support for some time on an issue with a MyData machine. Seems that this My9 likes to skip an 0402 placement at a rate of ~ 1000/million. Profile: MyData My9 Mechanical centering Midas only

MyData Missing Placements

Electronics Forum | Tue Jul 10 16:13:52 EDT 2007 | bk

Hi folks, I've been bouncing off of MyData > technical support for some time on an issue with > a MyData machine. Seems that this My9 likes to > skip an 0402 placement at a rate of ~ > 1000/million. > > Profile: MyData > My9 Mechanical ce

fiducial mark

Electronics Forum | Tue Mar 02 22:40:52 EST 2004 | pdeuel

To clean up other replys I will add that some most all machines have global correction. Most placements are an off sets from pcb 0,0 usually the lower left corner of the board. When the machine locates the fiduitals and these fids are not exactly whe

What to buy

Electronics Forum | Fri Mar 16 17:22:47 EDT 2007 | Cmiller

James, I respectfully disagree with you. Rick, you are correct. Personaly I liked that Universal published prices for their machines a few years ago. Im not sure if they still do and there may still be "deals" to be made. If someone was buying ten of

solder paste

Electronics Forum | Wed Jul 27 09:58:05 EDT 2011 | davef

Pressure printing systems Conventional stencil printing techniques have fundamental limitations as regards paste handling: The volume of paste available for printing is limited, so frequent replenishment is necessary Paste is difficult to c

  1  

mydata lower end point not repeatable searches for Companies, Equipment, Machines, Suppliers & Information

Baja Bid Auction JUL 9-10, 2024

High Precision Fluid Dispensers
Selective Soldering Nozzles

Wave Soldering 101 Training Course
PCB Handling Machine with CE

World's Best Reflow Oven Customizable for Unique Applications
2024 Eptac IPC Certification Training Schedule

Reflow Soldering 101 Training Course
Electronic Solutions R3

Low-cost, self-paced, online training on electronics manufacturing fundamentals