Electronics Forum: mydata midas (Page 1 of 5)

mydata 19 error

Electronics Forum | Thu Feb 20 13:25:18 EST 2014 | brendansales

Dear Rob, Thank you for your quick response! There were Z locks on the Midas head area, 2 little solenoids like you mentioned. Previously I had the first error code (F-AXIS-C/9) and after fiddling around, randomly manual unlock the Z locks it came

mydata 19 error

Electronics Forum | Thu Feb 13 00:43:06 EST 2014 | brendansales

Centering motor about to fail or has failed. > Centering motor about to fail or has failed. Hey Rdubya, Thanks for your help! Apparently that was not the problem. The Midas head had to be all the way down below the lower locking solenoid. After

mydata 19 error

Electronics Forum | Wed Feb 19 09:52:45 EST 2014 | brendansales

Dear Rob, Got to the maintenance menu, under the Motor section, I selected Z motor and tried to initiate motor, there was no movement on the machine and I had the error message as below: F-MOT-MSETDYN Z/12: Position counter dead I suspect that ser

Placing domed parts with mydata

Electronics Forum | Tue Feb 03 15:28:36 EST 2009 | kpm135

I agree, I'd try placing them with the midas or z-fi head depending what you have. Try using the mechanical centering in the zero angle with a low strength to move it straight. You'll probably have better luck finding a tool that will work on the hea

Z force sensor error mydata 11

Electronics Forum | Tue Feb 18 14:37:41 EST 2020 | bk

What type of head do you have on your machine a midas head or a zi-fi head? Regardless of which you do have I would make sure that the head is clean where to tools go into the head. Use a soft swab or something similar so you do not damage the z forc

mydata disable a bad Hydra setup to continue running

Electronics Forum | Tue Dec 21 12:28:11 EST 2021 | vtdivtecs

hey all, I had a comically bad failure yesterday while working with my pick and place, a part got dropped at exactly the wrong moment and flung a bracket up into the tool path, severely damaging the hydra controlboard that is next to the x camera. T

Mydata - Level too high in pick

Electronics Forum | Wed Jul 18 14:55:30 EDT 2012 | mikesewell

We bought from Mydata and recently had a new Midas head put in by Mydata and I've been on the phone with tech support. This has been a intermittent issue that's been hard to pin down.

Mydata centering jaws causing ESD and part damage

Electronics Forum | Sat Nov 08 00:28:25 EST 2014 | padawanlinuxero

Hello We a Mydata and put all kinda of components with the midas unit, but never had problems with ESD, and some of them are very delicate parts, perhaps like our colleague said perhaps you should look at the trays or feeders that you are using, pe

Mydata - Level too high in pick

Electronics Forum | Tue Aug 28 11:03:40 EDT 2012 | mikesewell

The problem is still intermittent. It has a new MIDAS head, installed and calibrated by Mydata, FWIW. Usually we work around it by moving parts upstream (Fuji AIM). I'll post an update when I finally chase the issue down.

F-MOT-MSETDYN Theta/12: No axis movement detected by transducer

Electronics Forum | Thu Feb 06 20:23:35 EST 2020 | bilalfarooqi

Hey everyone, We use a MyData MY12 machine and we are experiencing a problem with the Midas head. I recently replaced a torn vacuum tube that goes on the zfib card. The machine worked perfectly for a day and a half but now MY12 has completely stoppe

  1 2 3 4 5 Next

mydata midas searches for Companies, Equipment, Machines, Suppliers & Information