"nozzle" search results in the Electronics Forums

2071 results found for "nozzle" in the Electronics Forums

Order by: Relevancy |   Date

Siplace PnP

Nov 27, 2019 |

Problem with recognition on Emerald-X

May 10, 2019 | If standard nozzles are not able to handle a component perfectly, you can always get a customized no

Topaz X error

Feb 13, 2019 | My recollection is fuzzy, but don't the heads go down first, then the nozzle? If that's true, di

Picking and placing coils with a universal In-Line 7

Jan 24, 2019 | We can handle this challenge. If you would like to get an RFQ on a custom nozzle, please complete o

Flason SMT Products

Oct 4, 2018 |

0201 placement by Fuji CP643 Machine

Jul 26, 2018 | Load part on 0201 feeder Install .4mm nozzles in machine Load program and press start button.


Apr 12, 2018 | Juki is well supported in the US Stephen. When you get sorted out then come to us for custom nozzles


Mar 21, 2018 | Yep, fortunately we have a very good supplier in China for nozzles and feeders, otherwise it wouldn'

full nitrogen tunnel

Jan 24, 2018 |

LED sticking into carrier tape

Aug 1, 2017 | We are using a custom made nozzle, designed for this particular LED. The dome of the LED is also

Samsung CP45FV Neo

Mar 7, 2017 | The mirror should stay open. go to sys setup go to head go t nozzle check settings. that is were

Pick & Place cycle

Nov 8, 2016 |

Topaz Xi Place QFP

Oct 4, 2016 |


Jun 23, 2016 | Could be a partially clogged nozzle. Try disassembling the nozzle and thoroughly cleaning it. If t

Universal GSM and 0402/0201 Placement

Jan 19, 2015 | We can offer several nozzles to assist with the placement of 0402/0201 components in the four-spindl

Universal GSM and 0402/0201 Placement

Jan 16, 2015 | It's a four-spindle head. I've already learned the joys of the size of the nozzles...on a job that

Universal GSM 2

Oct 13, 2014 |

Universal GSM 2

Oct 13, 2014 |

chip placed upside down

Jun 10, 2014 | In our assumption also, nozzle is magnetized because the chip termination is made up of alloy so pos

ERSA Selective Solder questions

Aug 28, 2013 | i've a competitor selective soldering and i would like test the adique acide to clean the nozzle. H

Juki Laser Alignment

May 15, 2013 | Also make sure nozzle retraction is ok, if nozzle shafts stick at different heights can effect laser

QFP on going on square (now and again)

Apr 3, 2013 | Thank you for that, I see the #106 nozzle looks in better shape (with the rubber) I might try that n

QFP on going on square (now and again)

Apr 2, 2013 | This is where I purchase nozzles for our Jukis. You don't have to purchase the entire nozzle assemb

Selective Soldering

Sep 19, 2012 |

Quad IVc Part rejection issue

Aug 18, 2012 | When I see this on my QSP2 it is always caused by the nozzle not seating ideally but I tend to set m

Topaz X Head Optimization

Apr 5, 2012 | I have told the Topaz that it has 73 nozzles installed, and selected to use 73 nozzles for the LED's

Topaz X Head Optimization

Apr 5, 2012 | Hello! Did you try to pick all parts with the same type of nozzle? The LEDs are not so big that y

Panasonic CM Users

Mar 20, 2012 |


Mar 5, 2012 | Using the 72A FNC nozzles to place 3216 resistors, and 74F nozzles to place PLCC6 LED's. The LED's

Placing Luxeon Rebel

May 11, 2011 | LED sticking in nozzles are such a problem, seem everyone has issues with this from time to time.

FLexJet pickup problems

Apr 29, 2011 |

How to place cylindrical (MELF) parts on Quad P&P

Nov 5, 2010 | It has been a while but I think it is the "BAS" nozzle, a nozzle with a seal on the bottom and possi

philips Eclipse-II

May 29, 2010 | Mch Adjust > Adjust Target > Laser Unit > Nozzle Position. Here the laser will automatically detect

Placing Luxeon Rebel

Mar 31, 2010 | I worked on a nozzle for one of these LEDs in the past. I seem to remember that there are raised sur

Glue on 0402 components

Nov 3, 2009 | We have never dispensed adhesive for 0402, but here's your rules of thumb: * Nozzle diameter should

Inconsistent mounting on TOPAZ-X

Nov 11, 2008 | Is the package too large for the nozzle? They can rotate (or just fly off) after centering if they'r

Problems placing PLCC4 parts with Fuji IP1 - any help/ideas?

Oct 16, 2008 | Is the nozzle used to pick the offending used to pick other parts in this program? Have had experie


Oct 1, 2008 | we need a soldering nozzle for this package that can be placed by the rework machine on a pads of t

QUAD 4C T axis

Aug 4, 2008 | Miro, The video has nothing to do with the Quadalign. On a good startup and with no nozzle instal


Jul 22, 2008 | 0402 on CP643 is not that good.... We use the Fuji NXT for this part. However, nozzle configuration

Solder Splash

Jun 16, 2008 | I am using TopazX2, placing 0603 caps with #72 FNC nozzles. Sometimes, there is solder splash aroun

Topaz placement event sequence question (long, rambling)

Sep 14, 2007 | 100% positive. First thing I did was check the nozzle, plus it was happening with all nozzles on hea

Selective Conformal Coating System - GPD SimpleCoat

MPM SMT screen printer parts