Electronics Forum: omniflo fan motor (Page 1 of 5)

Heller 1500/1809 MKIII blower fan

Electronics Forum | Wed Feb 02 19:55:31 EST 2022 | dwl

you may also want to try replacing the Motor capacitor. This is often the culprit on those blower motors. I found them on Amazon for $3. much better then $450 for a new motor.

Heller 1500/1809 MKIII blower fan

Electronics Forum | Tue Jan 11 13:29:45 EST 2022 | bmalhi

You can purchase full motor assemblies directly from Heller. Please contact service with oven serial numbers and motor location ServiceNJ@hellerindustries.com.

Omniflo motor

Electronics Forum | Wed Mar 02 04:32:07 EST 2005 | Hannu

Hi all We have an Omniflo 5 (-97 vintage) with pin chain conveyor. Lately the chain drive motor has started to emit some chirping noises, as if there were a bearing running dry or something. Is there some kind of maintenance schedule specified for t

Omniflo motor

Electronics Forum | Wed Mar 02 06:21:44 EST 2005 | pjc

Why don't you ask the mfr.'s tech support ? http://www.speedlinetech.com

Omniflo motor

Electronics Forum | Thu Mar 03 11:08:34 EST 2005 | Slow Ride

It's your brushes. Had the same thing happen not too long ago. Also, fill that gear box.

Omniflo motor

Electronics Forum | Thu Mar 03 09:58:59 EST 2005 | Marc

The gears should be wet. This gear box acts like a rear end axle. Not sure of the lubricant but it is like a red transission lube, comes in as complete unit from supplier. You can't get the lube from Speedline since it is sold as a complete unit.

Omniflo 5 high temperature warning

Electronics Forum | Mon Sep 01 04:55:20 EDT 2008 | benefon

Hello all Our Omni 5 has given the 'Cooling module high temp' warning twice during the past month. I suspect that the blower motor is the culprit but have not been able to verify this because the oven has started up normally after acknowledging the

Mydata TP11 UFP hardware initiation failure

Electronics Forum | Thu Jul 20 11:18:43 EDT 2006 | ev

Paul, the error says "MOT1-38-247 MSETDYNX: Xwagon fan not working." I have checked...the X motor fan and it is working...the fan behind the PAIB board is also working...I checked this because there is a connector marked X wagon fan on the PAIB boa

Omniflo 5 conveyor

Electronics Forum | Thu Mar 23 23:21:10 EST 2006 | AR

100 cm/min) the motor runs without complaint. Too bad we run the conveyor as slowly as 10 cm/min... I'll try replacing the control board next when I get my hands on one.

Omniflo 5 conveyor

Electronics Forum | Mon Mar 20 06:21:42 EST 2006 | AR

Have a problem with Omniflo 5 (-97 vintage) pin chain conveyor. Occasionally the conveyor stops for a second or two, then makes a slight jerk, then stops again, makes a jerk etc. Then suddenly the problem goes away only to return next day (we switch

  1 2 3 4 5 Next

omniflo fan motor searches for Companies, Equipment, Machines, Suppliers & Information

Selective soldering solutions with Jade soldering machine

Benchtop Fluid Dispenser
Selective soldering solutions with Jade soldering machine

Component Placement 101 Training Course
Equipment Auction - Eagle Comtronics: Low-Use Electronic Assembly & Machining Facility 2019 Europlacer iineo + Placement Machine  Test & Inspection: Agilent | Tektronix | Mantis Machine Shop: Haas VF3 | Haas SL-20 | Mult. Lathes

Best Reflow Oven
PCB separator

Find a wide selection of nozzles, solder materials, storage solutions and more at SALESCON