Electronics Forum: packing (Page 1 of 45)

Silica gel in final packing

Electronics Forum | Mon Jun 30 22:02:43 EDT 2003 | davef

If you don't seal your packaging, the silica gel will try to remove the moisture from the air and will become saturated pretty quickly. There is no requirement that you pack/ship with dessicants. Some customers require such things though. Why do y

Silica gel in final packing

Electronics Forum | Sat Jun 28 22:52:34 EDT 2003 | ramanandkini

We have an Electromechanical assembly (clock) that has a step motor on the board. This electromechanical assembly is assembled in a screw less plastic moulded casing. The plastic casing is neither air tight nor water proof. The board is with SMOBC+ H

Silica gel in final packing

Electronics Forum | Wed Jul 02 06:56:34 EDT 2003 | davef

There's nothing wrong doing about adding a dessicant. You'll need to: * Seal the bag. [you may end-up needing a moisture barrier bag] * Select a dessicant packaging that is ESD dissipative.

PCB packing / shipping standards?

Electronics Forum | Fri Aug 06 11:25:09 EDT 2004 | reg

Hello. I'm trying to find out if there are any standards with regards to how a PCB is packaged and shipped. I'm particulary looking for info in whether or not ESD bags are required for an assembly in a metal enclosure. Thanks.

PCB packing / shipping standards?

Electronics Forum | Fri Aug 06 11:50:22 EDT 2004 | carterhoward

Hello I haven�t seen any spec for the shipment of enclosures I not absolutely positive but if it�s shipping in a metal enclosure that should act as a faraday cage. The assembled enclosure�s we ship are usually just warped in � pink foam. Hope thi

Silica gel in final packing

Electronics Forum | Tue Jul 01 21:06:12 EDT 2003 | ramanandkini

My customer just assembles it to the car. We want to use the silica gel to avoid moisture since the assembled part (clock) reach him via ship after 50 days. The electronic circuit board has no conformal coatings at present. We are working on that. Ou

Recycling of Waste Packing Material

Electronics Forum | Thu Feb 24 14:42:56 EST 2000 | Ashok Dhawan

We are looking for a source which can accept our packing material ( PVC tubings, Chip Trays, reels and spools , PCB waste rails from depanalization). Anybody, who is currently using a recycling manufacturer for these packing wastes. Our intent is:

Recycling of Waste Packing Material

Electronics Forum | Thu Feb 24 14:42:56 EST 2000 | Ashok Dhawan

We are looking for a source which can accept our packing material ( PVC tubings, Chip Trays, reels and spools , PCB waste rails from depanalization). Anybody, who is currently using a recycling manufacturer for these packing wastes. Our intent is:

Glass pack Diodes

Electronics Forum | Mon May 20 13:48:43 EDT 2002 | sbuckley

What is the recommended prep for a through-hole glass pack diode? Should a stand-off be used or can it lay flat on surface of the pcb?

Lifted Lead

Electronics Forum | Tue Sep 14 06:08:46 EDT 2004 | sc

The general control on QFP fine-pitch coplanarity is +3mils. suggest to look at the re-use of thrown out component from SMT machine. If the component pack in std pack, then most probably the lifted is due to processing, not incoming as the packaging

  1 2 3 4 5 6 7 8 9 10 Next

packing searches for Companies, Equipment, Machines, Suppliers & Information

Voidless Reflow Soldering

High Throughput Reflow Oven
SMT feeders

Best Reflow Oven
SMT fluid dispenser

Vacuum Tweezers Online Store