Electronics Forum: pad lifting (Page 1 of 22)

BGA pads lifting from PCB

Electronics Forum | Wed Jul 01 12:26:52 EDT 2009 | ewchong

can anyone suggest possible causes or further analysis for the lifted pads in attached picture. thanks.

BGA pads lifting from PCB

Electronics Forum | Thu Jul 02 13:10:22 EDT 2009 | kpm135

On first glance it looks like those particular pads were not attached to any traces. If I had to guess I would say that your rework profile got hot enough to melt away the glue holding the pads to the board and they came away with your part when you

BGA pads lifting from PCB

Electronics Forum | Thu Jul 02 16:01:57 EDT 2009 | ewchong

thanks kpm. agree the cause of those pads lifting. all of them were no connects so they cannot be the cause of the electrical failure. when the bga was removed, all the solder balls on the pcb turned into conical shape due to the separation, except

BGA pads lifting from PCB

Electronics Forum | Tue Jul 07 08:42:49 EDT 2009 | ewchong

kpm, you are probably right. under magnification those two pads show some exposed copper which means that they were contaminated or had insufficient solder paste before reflow.

BGA pads lifting from PCB

Electronics Forum | Tue Jul 07 05:55:34 EDT 2009 | kpm135

I agree with your assessment of the two pins with irregular solder. The head-in-pillow or broken joint are both probable events for your defect. At this point in the process it will probably be difficult to pinpoint the exact cause. If it was a broke

SOT-223 Flux trapped under part and lifting off pads

Electronics Forum | Wed Sep 29 09:29:47 EDT 2010 | swag

Take a few parts from the reel and look close at the parts to make sure the bottom surface of the leads is below the bottom surface of the body.

SOT-223 Flux trapped under part and lifting off pads

Electronics Forum | Thu Sep 30 11:30:46 EDT 2010 | babe7362000

Take a few parts from the reel and look close at > the parts to make sure the bottom surface of the > leads is below the bottom surface of the body. Yes I did that and they are below the body. I found the problem I think. The solder mask is abo

SOT-223 Flux trapped under part and lifting off pads

Electronics Forum | Wed Sep 29 08:26:03 EDT 2010 | babe7362000

We are Currently running a Board and it seems that the SOT-223's on the bottom side have flux and water trapped under the part. Nothing has changed in our process and this is the only board that it is happening on. We are using Kester R562 water wa

pad board separation

Electronics Forum | Fri Mar 24 08:32:17 EST 2006 | davef

Lifted pads are almost always caused by pad to substrate adhesion likely degraded significantly after too much heat. Poorly trained operators armed with soldering irons can do this expertly.

sri repairs pad repairs

Electronics Forum | Tue May 19 03:19:33 EDT 2009 | cunningham

Has anyone used a hot press to bond new pads to the boards if they have been lifted? we have one and have tried and carried out some DOE's on FR4 boards but when trying the same settings on Polyamide they basically fell of can anyone give any pointe

  1 2 3 4 5 6 7 8 9 10 Next

pad lifting searches for Companies, Equipment, Machines, Suppliers & Information

Equipment Auction - Eagle Comtronics: Low-Use Electronic Assembly & Machining Facility 2019 Europlacer iineo + Placement Machine  Test & Inspection: Agilent | Tektronix | Mantis Machine Shop: Haas VF3 | Haas SL-20 | Mult. Lathes

World's Best Reflow Oven Customizable for Unique Applications
Global manufacturing solutions provider

High Precision Fluid Dispensers
design with ease with Win Source obselete parts and supplies

Thermal Transfer Materials.