pad size

"pad size" search results in the Electronics Forums



883 results found for "pad size" in the Electronics Forums

Order by: Relevancy |   Date

stander pad size required for 2835 led

Jan 11, 2019 | what is the standard for pad size of SMD chip type components

SMD coil land pattern recommendation size

Sep 18, 2017 | I would go with wire thickness + 0.4 to 0.8 mm for pad width, and pre-tinned lenght + 0.5mm what se

Stencil Aperture Size vs Copper Pad Size

Aug 9, 2016 | this really depends on the pad sizes. You can see 15 different pad sizes for the same component pack

Stencil Aperture Size vs Copper Pad Size

Aug 8, 2016 | What should be solder paste stencil aperture proper size in comparison with PCB copper pad for lead

pad cratering

Jul 1, 2015 | hi, the last post on pad cratering dates from 2012. We have (likely similar) problems with a RoHS

BGA Pad with Irregular Pad size

Sep 7, 2014 | Edri PCBA design and pad geometry is one of the critical factors for BGAs. Typically the pad size

BGA Pad with Irregular Pad size

Sep 5, 2014 | Hi, Edri, It's not uncommon for PCB fab houses to change pad sizes like that, due to design const

BGA Pad with Irregular Pad size

Sep 5, 2014 | Hi, We have a problem with our BGA Pad. Our PWB manufacturer make the BGA Pad in irregular form.

BGA pad size too large??

Sep 7, 2011 |

Suface mount shield pad size

Apr 6, 2009 | For your responce on OrbelE-Z SHIELD. Are you referenceing the PCB pad is 1 to 1 with the fence foo

Suface mount shield pad size

Apr 2, 2009 | On Orbel E-Z SHIELD, Surface mount two-piece fence and cover: Make the pads 1:1 with the pads on the

Land size

Jul 10, 2008 | Try IPC SM 782. Also most parts manufacturers should be able to provide you a pad design.

Land size

Jul 9, 2008 |

Land size

Jul 7, 2008 | Most QFP 128s have a 0.16mm wide lead. Might have to modify your pads if you'r buying some odd ball

Land size

Jul 7, 2008 | Hi All, Can anyone advise the spec for land size of a lead 0.2mm in width? I am placing a TQFP12

glue size

Jan 2, 2007 | We had a supplier that put a [fuzzy and of variable height) line of ss between all chip R and C pads

glue size

Dec 28, 2006 | So I'm the only one that's had crappy piles of silkscreen between pads?

BGA pad size

Jun 21, 2005 |

BGA pad size

Jun 18, 2005 |

BGA pad size

Jun 17, 2005 |

BGA pad size

Jun 17, 2005 |

BGA pad size

Jun 16, 2005 | Josh: You're correct it's tough to describe the layout of the BGA pads and traces. We wouldn't b

BGA pad size

Jun 14, 2005 |

BGA pad size

Jun 14, 2005 |

BGA pad size

Jun 14, 2005 |

BGA pad size

Jun 14, 2005 |

BGA pad size

Jun 14, 2005 | Morning all, just took a look at a new board we just got in and the there are different pad areas un

Deciding On pad size using just the component footprint

Jul 24, 2004 | We believe that many manufacturers' recommended pads should be close to the last resort. Recommenda

Via in pad

Jun 11, 2004 | We currently have an issue with via's in pads which we have been living with for some time. The prob

Stencil Aperture Sizes

Jan 21, 2004 |

BGA PCB Pad size

Jan 30, 2003 |

BGA PCB Pad size

Jan 27, 2003 |

BGA PCB Pad size

Jan 26, 2003 |

BGA PCB Pad size

Jan 19, 2003 | You shouldn't freak. You want the pads on both sides of the BGA ball the same so that the torgue

BGA PCB Pad size

Jan 17, 2003 |

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

Dual Lane Reflow Oven

Online IPC Training & Certification