Electronics Forum: part in (Page 1 of 43)

Leaded part in no lead process

Electronics Forum | Mon Nov 29 10:13:02 EST 2010 | vetteboy86

My research starts here. I'm just beginning to research the effects of using a leaded part in a no lead process. Before I began, I know there are temperature differences. The part in question has a 260 C spec. Next I would like to find out if any c

Throw out part in NXT machine

Electronics Forum | Tue Dec 08 15:02:20 EST 2020 | btmzzulp

One of category throw out part in NXT fuji is Dislodge, it is not so clear, what is root cause of this dislodge and how it happened, thank you

Anyone has this part 88W8790-A1-BLF2C00-P162 in stock? We need 12Kpcs

Electronics Forum | Tue Aug 11 12:55:39 EDT 2020 | alanyang

We need 12Kpcs 88W8790-A1-BLF2C00-P162 from Marvell Avastar. If you have it in stock, could you pls provide photoes of the part and its detailed datasheet. https://pcbboardassembly.com

part x-out from board when exit in mirtec offline pc.

Electronics Forum | Fri Dec 27 07:20:38 EST 2019 | dipak123

We have Mirtec MV-6 OMNI machine. If programer changes in part number ,then that part x-out from it's place.Value of X & Y incresed 10X compare to other parts in ATT.

Part sliding in reflow?

Electronics Forum | Wed Apr 18 01:07:25 EDT 2001 | MW

I some something like this. My package was not flat the belly of the body rested on the PCB. We found that every 4-5 part would wander to the side. What was puzzling is that the blowers would have blown it the opposite side. ultumately we proved

Component Loss in CP643

Electronics Forum | Tue Sep 27 14:42:56 EDT 2005 | paulbendemire

20%) on particular parts (e.g. 0402 caps) by looking to the part data. After this, we have another threshold (10-20%) that I am continuing to look into. Feeders are suspect, though part data could also be involved, just to a lesser extent than with

Component Loss in CP643

Electronics Forum | Tue Sep 27 15:57:43 EDT 2005 | stepheniii

Ceramic caps are denser than most other components and I"ve found the tops can be slightly rounded. You may want to slow down the turret speed for some parts. Do you ever get a location where there should be a part but there is not? If the part fly

Smt parts in strips

Electronics Forum | Wed May 02 09:25:09 EDT 2012 | tbouslog

Our company has recently changed the way our cage gives our SMT Department their parts to try to better control inventory. SMT now instead of recieving reels recieves strips with only 2-20 extra parts depending and the size/cost of the part. Does any

Losing parts in reflow

Electronics Forum | Wed Jun 13 15:56:35 EDT 2007 | ck_the_flip

I experienced this with a high-mass capacitor. I was able to turn down the bottom-side convection (around 50�C lower than each of the top-side heaters), and able to NOT lose any parts. I got the bottom-side part just slightly over liquidus, and min

Re: Misalignment in TBGA?

Electronics Forum | Sun Aug 02 12:24:23 EDT 1998 | Bob Willis

Sorry all the parts I have processed are just like standard BGA just swing back into possition unless they are placed off the pads and touching the next pads. All my parts have had heat sinks and are the same weight as PBGA. Are your parts light. If

  1 2 3 4 5 6 7 8 9 10 Next

part in searches for Companies, Equipment, Machines, Suppliers & Information