Electronics Forum: pass (Page 121 of 142)

Samsung CP 45 NEO, servo motors

Electronics Forum | Thu Mar 21 12:09:28 EDT 2019 | alexcouto

Hello Bukas, thanks again. Since at an early stage I switched heads # 1 and # 6 and they are not compatible, then I went through the manual and figured out why. in order to start at the beginning and check that it had not damaged anything, I put the

AOI Omron VT-RNS-pt - Help with some basic programming questions

Electronics Forum | Thu Oct 10 10:27:24 EDT 2019 | tsvetan

Omron is probably worst choice for AOI unless you have long series. Requires too much debug and there is always compromise between setting sharp criterias and get lot of fake errors or setting lose criterias and get boards with defects to pass OK. Y

AOI Omron VT-RNS-pt - Help with some basic programming questions

Electronics Forum | Fri Oct 11 03:56:39 EDT 2019 | chrislandafont

Hi Tsvetan, Yes, I've heard it's difficult to program but good once it gets going. At the moment, I'm working through the manuals, but can't find a step by step guide, just lots of reference material on how to do things, but not knowing what orde

DEK HORIZON 265 Squeege Pressure question

Electronics Forum | Sat Nov 09 19:37:52 EST 2019 | kylehunter

> the issue is the calibration. What you set it for > has to match what it actually reads or you get > the error screen at the end of every pass. If > you go into the maintenance menu ( using the key > next to the system button )

New Facility Advise/Questions

Electronics Forum | Fri Dec 27 11:21:14 EST 2019 | kylehunter

> If you're going to vent through a single > exhaust/fan combo, I would recommend spending the > money, and getting an HVAC company in there to > size the exhaust fan, and duct work. It'll pay > dividends for you in the future. W

solder ball

Electronics Forum | Mon Dec 30 23:37:47 EST 2019 | agoesfirmanto

Hello All, I am a SMT Engineer from Indonesia, I am facing the problem of soldering balls in only one IC location, in other areas there are none. solder ball defect almost 30%. I have done several actions but failed to reduce the solder ball. 1.

Re: Setting up solder material evaluation (suggestions?)

Electronics Forum | Tue May 04 14:42:58 EDT 1999 | Chrys Shea

I am about to embark on an effort to evaluate 3 different solder material suppliers and their recommended materials for our assembly process, in an effort to find the best supplier/material. We do mixed technology, with NOCLEAN chemistry so I wi

Re: Setting up solder material evaluation (suggestions?)

Electronics Forum | Mon May 10 07:53:48 EDT 1999 | Timothy O'Neill

I am about to embark on an effort to evaluate 3 different solder material suppliers and their recommended materials for our assembly process, in an effort to find the best supplier/material. We do mixed technology, with NOCLEAN chemistry so I

Re: Setting up solder material evaluation (suggestions?)

Electronics Forum | Mon May 10 08:00:14 EDT 1999 | Timothy O'Neill

I am about to embark on an effort to evaluate 3 different solder material suppliers and their recommended materials for our assembly process, in an effort to find the best supplier/material. We do mixed technology, with NOCLEAN chemistry so

Re: Fond Farwell II (Why I hate aggresive sales and marketing)

Electronics Forum | Mon Apr 19 13:05:31 EDT 1999 | Bob

Steve, Like you, I am sick, sick, sick of marketing. I can't go on the Internet, to a ball game or my local 7-11 without being bombarded with marketing. 7-11? Would you belive I went there to buy a Sunday paper yesterday and now they have a 27" mo


pass searches for Companies, Equipment, Machines, Suppliers & Information