Electronics Forum: pcb panel v-score routing (Page 1 of 8)

PCB routing

Electronics Forum | Wed Aug 30 13:26:29 EDT 2017 | fuji_user_2014

Hello Gurus, I'm looking for information on FOD generated by routers, more specifically a vacuum equipped Cencorp 1000BR. I want to ensure that this machine can route a populated panel without needing a wash afterwards in order to meet IPC CL3 sta

Cleaning PCB's after routing

Electronics Forum | Fri May 22 22:18:18 EDT 1998 | David Newman

Hello, I am looking for suggestions for cleaning pcb's after the routing (fabrication) process. Keep in mind that these pcb do not have components intalled on them yet. We have considered pre-drilling the routing plunge points, but cost and capacity

Optimal PCB design for routing

Electronics Forum | Tue Oct 29 08:07:53 EDT 2013 | cyber_wolf

Are there a set of guidelines for optimizing panel design for tabs that will be removed with a board router ? In other words we need to know how to layout the tabs. Thanks

Optimal PCB design for routing

Electronics Forum | Tue Nov 26 15:32:41 EST 2013 | boriskilk

As with most questions the answer is; it depends. Provided not too many boards are set onto a panel we use a .10" router gap around the PCB and .10" wide perforated tabs. We do request customers specify where they do not want tabs to ensure no breako

Re: Cleaning PCB's after routing

Electronics Forum | Thu Jun 04 22:18:40 EDT 1998 | David Newman

1/8" cutters, although they can only be used with our newer height-controlled machines. 3. Reduction of operating parameters. Reduced Z-axis plunge rates for the larger cutter sizes. 4. Addition of a 1/2 sec. dwell at the plunges. The small pause he

Re: Cleaning PCB's after routing

Electronics Forum | Sun May 24 06:02:33 EDT 1998 | Earl Moon

| Hello, | I am looking for suggestions for cleaning pcb's after the routing (fabrication) process. Keep in mind that these pcb do not have components intalled on them yet. | We have considered pre-drilling the routing plunge points, but cost and ca

Re: Cleaning PCB's after routing

Electronics Forum | Tue Jun 09 17:01:02 EDT 1998 | Earl Moon

1/8" cutters, although they can only be used | with our newer height-controlled machines. | 3. Reduction of operating parameters. Reduced Z-axis plunge rates for the | larger cutter sizes. | 4. Addition of a 1/2 sec. dwell at the plunges. The small

pcb manufacturing

Electronics Forum | Wed Jan 13 04:27:00 EST 2016 | crystalpcb

Hi Here is our factory production capability: Shenze Electronic PCB Specification Layer Count 1 to 35 Layers Material Brand Shengyi,KB,GRACE,ISOLA,Rogers,Taconic,ARLLON,Bergquist Base Material FR-4(TG135,TG150,TG170,TG180),Halogen Free FR-4,Ceramic

Repair of FR4 double-sided pcb

Electronics Forum | Thu Aug 22 22:10:26 EDT 2002 | davef

Ooooow! �Can it be fixed?� Good question. How BAD did you damage it? * Since you are asking this question, I am NOT inspired by the potential that you have the skills to fix the board. Go Jeff Ferry�s site at Circuit Repair Center [If you can�t f

Mechanical Delamination at de-panel

Electronics Forum | Tue Jun 03 10:28:09 EDT 2014 | swag

Incoming inspection: Look for flaws and measure position of v-score as well as depth. If v-scored on both sides of panel, make sure v-scores are in alignment. Follow the PCB thru all processes inspecting after each stage of processing, especially

  1 2 3 4 5 6 7 8 Next

pcb panel v-score routing searches for Companies, Equipment, Machines, Suppliers & Information

Precision PCB Services, Inc
Precision PCB Services, Inc

Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.

Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider

1750 Mitchell Ave.
Oroville, CA USA

Phone: (888) 406-2830