Electronics Forum: peek (Page 1 of 2)

Ni/Sn plated parts

Electronics Forum | Tue Jun 15 08:22:39 EDT 2004 | jsmith01

The parts are dated Mar 20 2004. My profile hits a peek of around 232-240c and is above 225 for around 30 seconds.

Voiding In BGAs

Electronics Forum | Wed Nov 05 13:34:24 EST 2008 | ed_faranda

Exactly what should I look at in my reflow profile? Soak Times, TAL, Peek?!? I am right in the middle of the manufacturing specifications as far as my profile goes.

Re: Stencil Cleaner

Electronics Forum | Fri May 12 13:42:38 EDT 2000 | Steve Thomas

I also recommend that you take a peek at the archives, as stencil cleaners have been discussed a number of times. I also recommend that you check with your stencil manufacturers to determine exactly what cleaning process parameters are acceptable to

Placement machine comparison

Electronics Forum | Thu Jun 27 02:52:54 EDT 2002 | Darby

Take a peek at a Samsung CP45v before you make a decision. I'm running two before a CP40v. Runs very well. Clever software. Cheap. I'm also running two Tenryu/i-Pulse FV-7100 in line vintage 1999. Great machines but it may be some time before the sup

TM12 Feeder problem for MYDATA TP9-UPF

Electronics Forum | Fri Mar 27 09:37:15 EDT 2009 | cyber_wolf

There are pem nuts on the back side of the teddy bear face. One of them probably fell off and either shorted your main board or it is lodged in the belt and pulley that drives the advancing wheels. Take the front part of the feeder off that has the t

Re: Reflow glue and past.

Electronics Forum | Tue Feb 08 14:49:23 EST 2000 | Travis Slaughter

I have never tried this and wouldn�t really even want to consider it. Epoxy generally cures at around 160c in a fairly short amount of time, solder paste requires much more time and a peek temperature of about 210c or more in some cases. Curing you

Nozzle life?

Electronics Forum | Mon Feb 28 01:01:10 EST 2005 | //jh0n.

Actually, in thinking about what someone else had posted - I'm willing to bet that it's not that I'm losing parts and the nozzle is actually touching the paste, but more that since the nozzle peeks over the sides of the component slightly, especially

Need Help Operating CSM84VZ

Electronics Forum | Fri Jan 07 02:07:11 EST 2011 | tpappano

Wow, there is a floppy drive hiding inside? I took a peek inside my unit when I first got it and didn't notice one. I will take a closer look! My second unit, that I just got, came with a grab-bag of odds and ends, and I found a ms-dos based utilit

Question on Reflow Profile Development

Electronics Forum | Wed Jun 13 18:04:00 EDT 2001 | traviss

It is possible with a few universal profiles. I did this with 3 temperature ranges and 3 speeds for each, 9 profiles total. With this setup I could run any of about 150 boards most of them in the middle 3 profiles. My goal was to reduce change over i

Help CSM84 mechanical alignment

Electronics Forum | Fri May 04 19:23:28 EDT 2007 | darby

System > Machine Config > Mechanical OP > Head 3 Spec = Vision. Data In > System > Machine Config > Mechanical OP > M Centering 1 = Yes If your Centering unit is a two stage unit then also set M Centering 2 = Yes You should then be able to roughly

  1 2 Next

peek searches for Companies, Equipment, Machines, Suppliers & Information

Equipment Auction - Eagle Comtronics: Low-Use Electronic Assembly & Machining Facility 2019 Europlacer iineo + Placement Machine  Test & Inspection: Agilent | Tektronix | Mantis Machine Shop: Haas VF3 | Haas SL-20 | Mult. Lathes

Reflow Soldering 101 Training Course
Fluid Dispensing, Staking, TIM, Solder Paste

Stencil Printing 101 Training Course
PCB Handling Machine with CE

Best Reflow Oven
Global manufacturing solutions provider

High Throughput Reflow Oven
Solder Paste Dispensing

World's Best Reflow Oven Customizable for Unique Applications
Fully Automatic BGA Rework Station