Electronics Forum: pin and to and pad (Page 1 of 2)

QFN's and LGA's

Electronics Forum | Tue May 26 14:39:40 EDT 2009 | boloxis

QFN or MLFs are mainstream now, QFNs already evloved to much more complex versions now like matrix pins, stacked dice and flipchip versions. IPC 610D already includes them, just make sure the pins have solder plating, the PWB pads have soldermask in

BGA lands and ICT

Electronics Forum | Wed Mar 20 07:57:30 EST 2002 | davef

Purchase: 7095 - Design and Assembly Process Implementation for BGA's Make every effort to distribute the test pads, because if you keep them massed at the ball, it would be a bijundo kick in the BGA rear section, when all of those pins released.

tape and reel vendor

Electronics Forum | Tue Mar 30 10:43:21 EST 2004 | Robert

I could use some help too. I have a bunch of SMD 4 Pads Inductors from Central Technologies. The dimensions of the part is 11.30x13.9x6.9 . I've called four companies already and none were able to find a carrier for this part. These parts are on plas

BGA assembly and inspection

Electronics Forum | Thu Sep 07 03:57:39 EDT 2000 | Steven Cheung

Does anyone know of a freely-available document which discusses the main considerations of BGA assembly and inspection (x-ray?). l need to know about pad sizes and inspection standards and when to underfill and when not to etc.. l am looking at ass

help to id and purchase pcb transformer from LOWRANCE GPS

Electronics Forum | Sat Jun 25 15:20:03 EDT 2016 | skipper6567

I have a mini/micro transformer that is mounted on a pcb inside my lowrance gps/plotter. I have removed it from the pcb. It has 5 through hole pins, 3 pins out bottom one side and 2 pins out bottom on opposite side. The transformer has yellow tape ar

where to find older Siemens line transformer and equipment

Electronics Forum | Wed Apr 07 11:21:26 EDT 2004 | stefwitt

Hi Dilbert, it is a step up transformer from 3 phase 208 to 3 phase 380. Each machine does not draw more than 3 Amps per phase. However, circuit breakers are rated at 15 Amps. The transformer has three power outlets, each one has a Perilex (European)

qfp and soic joint Problem

Electronics Forum | Tue Apr 11 10:30:46 EDT 2000 | Jeremy Smith

I am having a problem with some joints on a 100 pin pqfp and few different soics on one particular board. When viewed a 8x with a "Mantis" inspection scope the joints look as though they wetted to the ic leg but when probed the leg will pop loose.

ICT and specifying PCBA testing

Electronics Forum | Fri Nov 18 12:35:15 EST 2011 | rway

As the article eludes to, you still need probe access to measure the pins with TestJet. One thing I wanted to add was the use of JTAG for use with Boundary Scan. Certain devices have JTAG capability, but not all JTAG devices are Boundary Scan compa

PLCC 44 and QFP 240 tilting problems

Electronics Forum | Sat Feb 17 14:21:54 EST 2007 | Muhammad Haris

Hi All, I am using YV100Xg YAMAHA Pick and Place Mounter Machine and I am facing a tilting problem of PLCC 84 and QFP 240 pins ICs. I deeply checked about their vision files and place them on the double sided tape and found them ACCURATE on their pad

Wave Soldering 14 and 16 Pin SOICs

Electronics Forum | Tue Mar 09 18:21:37 EST 1999 | Stan Levitsky

We will wave solder a board with SOIC14 and SOIC16 parts on the bottom. It has been difficult to find any specific wave solder process recommendations from manufacturers of the SOICs. The pad geometry utilizes theiving pads on both sides to reduce br

  1 2 Next

pin and to and pad searches for Companies, Equipment, Machines, Suppliers & Information

PCB Handling with CE

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.
2024 Eptac IPC Certification Training Schedule

Component Placement 101 Training Course
thru hole soldering and selective soldering needs

Reflow Soldering 101 Training Course
PCB separator

Private label coffee for your company - your logo & message on each bag!