Electronics Forum: positive lead error (Page 1 of 52)

SN100C alloy positive and negatives

Electronics Forum | Wed Dec 24 15:28:17 EST 2008 | edmentzer

We use SN100C for wave soldering and hand Lead free soldering and have had very good results. The wire cored solder for hand soldering flows good and makes very good solder joints. The SN100C in the wave solder machine also works very good. We use

SN100C alloy positive and negatives

Electronics Forum | Mon Dec 22 10:43:18 EST 2008 | etechsupply

I wanted to hear from users of the SN100C alloy to find out what they think is positive and negative about this lead free alloy. Thanks, Keith

MyData error

Electronics Forum | Thu Aug 14 13:49:26 EDT 2014 | dyoungquist

Motor control MSETDYN -> Initiate axis C -> Centering jaws 156 -> Motor timeout Did not reach specified position Hardware problem Looks like you have something wrong with the movement of your centering jaws.

MPM AP25Hie Pre Board Stop error

Electronics Forum | Mon Jul 30 17:32:34 EDT 2007 | chrisgriffin

When you teach the "teach boardstop Y" make sure the camera is seeing the leading edge of the board and not too close to the rails. It should calculate the pre-stop position correctly. I assume you have thoroughly checked the sensor. Also check th

Samsung QSA error

Electronics Forum | Mon Jun 12 17:54:17 EDT 2017 | simons

The machine does not move to the home position. Once we hit the "Home" button all three heads will move up to the "Home" position but then 5 to 10 seconds later the following error pops up "Error 1531 - Z Axis motor alarm" before any "xy" movement i

Topaz X error

Electronics Forum | Tue Feb 12 12:47:02 EST 2019 | slthomas

Someone with some more definitive knowledge of these machines will no doubt chime in at some point, but my thought was that the "A-table" is just a data table that stores I/O information. Thus, being "off in A-table YV100X:N2323 YV100XT:n2223" just m

MYDATA My9 Theta error

Electronics Forum | Mon Nov 19 17:43:16 EST 2012 | jaimebc

Theta error came back again during our first production run. Swaped motcards as a final attempt to find an easy fix and nothing. I swapped heads with another MYDATA to positively isolate the problem. And the theta error followed the head.

Topaz X error

Electronics Forum | Wed Feb 13 18:13:58 EST 2019 | slthomas

I'm trying to visualize how that machine is laid out. Do they all rotate together, on a belt, so that there's only one sensor for the theta (R) home position?

Quad IV-c feeder error

Electronics Forum | Sun Feb 03 07:39:27 EST 2019 | dfl

POCKET POSITION PROGRAMMING This procedure ensures the components are properly centered at the tape feeder pickup point (over spring stabilizer). NOTE: The feeder can be reset at any time by removing it from the feeder base and reinserting it. This

Meridian 1010 error code

Electronics Forum | Mon Jun 20 18:36:42 EDT 2005 | jsloot

Does anyone have any experience with a QUAD Meridian 1010? Our company has purchased a used machine. We have it installed and running almost smoothly. Getting an error code 3487, description is "Z axis target position in motion board is strange" Anyo

  1 2 3 4 5 6 7 8 9 10 Next

positive lead error searches for Companies, Equipment, Machines, Suppliers & Information

Best SMT Reflow Oven

High Resolution Fast Speed Industrial Cameras.
Reflow Oven

Nozzles, Feeders, Spare Parts - Siemens, Fuji, Juki, Yamaha, etc...
MSD Dry Cabinets

PCB Assembly Supplies - ONLINE STORE
Voidless Reflow Soldering

One-stop Platform For All Your Need For SMT - QYSMT