Electronics Forum: potted assembled pcb fail (Page 1 of 11)

ROSE testing pass / fail

Electronics Forum | Mon Feb 21 20:15:49 EST 2022 | arminski

since IPC-J-STD-001 RevH obsoleted the 1.56ug/cm2 UCL of ionic contamination tester in testing using ROSE test, how do you define the acceptable limit per PCB assembly? thanks

defects in pcb manufacturing

Electronics Forum | Sun Nov 01 01:33:52 EST 2009 | isd_jwendell

Just my opinion: Top pic - Solder mask registration WAY too far off, without a doubt I would reject. Bottom pic - I would worry that there was/is a contamination that caused the poor looking mask. This may be cosmetic only, but unknown. I would rej

Re: Ghost circuit shorts under smt resisters only when they are located on solder side of pcb (glued down)

Electronics Forum | Fri Jul 30 09:43:44 EDT 1999 | C.K.

| We are having a process related problem with pullup resistors on a controller card which has a I960 micro-processor. | The controller monitors signal inputs and it's own resources then blinks a LED to indicate its working. The problem is that after

SOIC FAIL

Electronics Forum | Wed Oct 27 02:13:21 EDT 2004 | Joseph

Dear all, The problematic IC being X-rays and shown excellent wetting with no solder voids. Meanwhile the samples to be sent for independent party to verify the failure, e.g. using SAM method. The condition of failure is the PCB assembly fail functi

Motherboard become NO POST when humidity increase to 90%

Electronics Forum | Tue Nov 24 19:07:12 EST 2009 | gregoryyork

I agree Patrick many people blame the assembly fluxes when it is some other hygroscopic chemistry left on the bare PCB such as surfactents from the HASL process these will do exactly what the guy reported in his post fail then cool down and pass ever

Pb-free wave soldering with SMD

Electronics Forum | Sat Nov 26 05:55:04 EST 2005 | milroyperera

Hi, Does any body have the experience with wave soldering a "Gold" plated PCB with SMD assembled on it? I`m experiencing massive bridging,icicles,Shadowing & Skipping. The present soldering angle is 6 deg:,pre heating rate is 2 deg/sec , Dwell time

30 Layer PCB with 70% fallout. Are the 30% good?

Electronics Forum | Thu Jan 28 15:08:32 EST 2010 | jamyboy

Hello All, Well we have a critical PCB assembly with 30 layers being produced by DDI. We just received word from the PCB shop that this unit only yielded 30% or basically 70% failed. Should we keep the 30% yield or have the shop rebuild al

Removing Component Part Number

Electronics Forum | Thu Mar 02 14:33:26 EST 2000 | Doug Philbrick

I have a customer wanting to hide the identity of a particular component on a PCB assembly. The product cannot be potted and since the PCB is the product he doesn't want to pour over that one chip for aesthetics reasons. Any ideas on ways to permanen

Removing Component Part Number

Electronics Forum | Thu Mar 02 14:33:26 EST 2000 | Doug Philbrick

I have a customer wanting to hide the identity of a particular component on a PCB assembly. The product cannot be potted and since the PCB is the product he doesn't want to pour over that one chip for aesthetics reasons. Any ideas on ways to permanen

High temp PCB coating needed

Electronics Forum | Tue Oct 16 10:06:41 EDT 2018 | emeto

Hello experts, I have an assembly that goes through pretty tough sterilization on regular basis. Currently I am using a two component material in potting process. I was wondering if you can help me with material that can handle high temp and humidit

  1 2 3 4 5 6 7 8 9 10 Next

potted assembled pcb fail searches for Companies, Equipment, Machines, Suppliers & Information

Precision PCB Services, Inc
Precision PCB Services, Inc

Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.

Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider

1750 Mitchell Ave.
Oroville, CA USA

Phone: (888) 406-2830

PCB Handling Machine with CE

Training online, at your facility, or at one of our worldwide training centers"
Circuit Board, PCB Assembly & electronics manufacturing service provider

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.
Encapsulation Dispensing, Dam and Fill, Glob Top, CSOB

We offer SMT Nozzles, feeders and spare parts globally. Find out more
High Throughput Reflow Oven

Reflow Soldering 101 Training Course
PCB Depanelizers

"Heller Korea"