Electronics Forum: power and converter (Page 1 of 15)

gerber converter to centroid

Electronics Forum | Fri Oct 20 11:44:40 EDT 2006 | sliebl

Anyone using Circuit Cam? We too are looking for a gerber/centroid converter. I used the demo of GraphiCode GC-PowerPlace and it works, but seems cumbersome. It's also difficult to substantiate the large capital cost of these programs without being v

power supply

Electronics Forum | Wed Feb 07 08:41:10 EST 2001 | dliechti

I have to design a power supply which converts 220V AC into 5V smothed DC. It has to be very small, so it shouldn't have a big transformer. Has somebody a scheme of a circuit? Thanks

I mounted the parts on the buck-boost DCDC converter and measured the characteristics

Electronics Forum | Tue Aug 23 03:29:37 EDT 2022 | samhe

I received a buck-boost DCDC board with an optical sensor from NextPCB, so I mounted the components and measured the efficiency. Table of contents Board received from NextPCB Solder paste printing Mounting of parts Reflow operation check Attaching

Heller 1088 power draw

Electronics Forum | Fri Mar 24 15:08:20 EDT 2023 | erikfriesen

The nameplate specs for a 2004 Heller 1088EXL show 240V 60A, and specify Largest Heater Load of 25A. As each of the 8 heater elements is 6000W or 9.5R, how does this really work? Obviously all 8 elements on would pull 200A, so does the machine only

Quad 4C power switch

Electronics Forum | Fri Sep 06 02:34:37 EDT 2013 | rollon65

Hi Marcelo The two machines I mentioned are the American type but they have an internal transformer fitted to convert from 110 to 220 Volts for U.K. Incidentally only one of the machines does it on a regular basis whilst the other one is mostly O.K

Quad IV-c power transformer

Electronics Forum | Fri Jan 25 08:54:33 EST 2019 | dfl

For the first time, I'm really looking at to the power transformer for the IV-C pick and place (the big big one, at the middle). As I understood, is this transformer converting the 220V to 127V? I realize that the camera monitor is 127V and the PC PS

CP4 jerks all axis after power up and reset sw...

Electronics Forum | Wed Apr 11 17:00:28 EDT 2012 | rodrigo

Hi all, Our cp4 moves rather violently (jerks) all axis when the reset sw is pressed after power up. I've got all sorts of errors after boot up: Servo amp error: D,X,Y, etc Overtravel D,X,Y, etc D clutch error, power off machine We've checked all

CP4 jerks all axis after power up and reset sw...

Electronics Forum | Thu Apr 12 15:21:12 EDT 2012 | jdengler

Have you tried to do a reset start? When Fuji's act weird the first place to start is a reset start, then re-load the Proper Status and Program. Jerry

CP4 jerks all axis after power up and reset sw...

Electronics Forum | Mon Apr 16 10:48:58 EDT 2012 | cyber_wolf

Sounds like a bad or out of adjustment servo amp.....

CP4 jerks all axis after power up and reset sw...

Electronics Forum | Thu Apr 12 17:49:35 EDT 2012 | rodrigo

I've done the Fuji flush. It does the same thing. We can not load proper again because it does not communicate with either the F4G or MCS/30. I was able to boot into mechanical mode at one point but now I can not do that either. This thing is drivi

  1 2 3 4 5 6 7 8 9 10 Next

power and converter searches for Companies, Equipment, Machines, Suppliers & Information

Pillarhouse USA for Selective Soldering Needs

Training online, at your facility, or at one of our worldwide training centers"
Selective Soldering Nozzles

High Throughput Reflow Oven
IPC Training & Certification - Blackfox

World's Best Reflow Oven Customizable for Unique Applications
best pcb reflow oven

Nozzles, Feeders, Spare Parts - Siemens, Fuji, Juki, Yamaha, etc...
PCB Depanelizers

Low-cost, self-paced, online training on electronics manufacturing fundamentals