Electronics Forum: pressure control/ fault (Page 1 of 22)

VIP98 fault

Electronics Forum | Wed Feb 11 06:37:10 EST 2009 | reflowtechnologies

Please check the following: 1.Power supply. 2.SSR control power. 3.OTP or over temp protection at the software. Maybe you set it at low so it reads over temp even at lower temp. If still not ok you may check BTU service engineers. Brian Riggs

Soltec 6622cc fault

Electronics Forum | Sat Jan 09 13:42:54 EST 2016 | aemery

Bill, Did you ever get this issue resolved? Electrovert is more my cup of tea, but I have completed a couple of pot replacements on the Vitronics waves. I remember on one machine after the retrofit the we were testing the machine and everything dro

Zevatech Z Axis fault

Electronics Forum | Mon Jun 29 19:36:08 EDT 2009 | proy

Are you sure it is the Z axis, and not the rotation, I had one machine which often did something similar, it would buzz loudly, especially if you touched or applied rotation pressure to the gear belt which rotates the head. It never caused any hard s

Zevatech Z Axis fault

Electronics Forum | Wed Jul 01 13:41:25 EDT 2009 | jlawson

Are you sure it is the Z axis, and not the > rotation, I had one machine which often did > something similar, it would buzz loudly, > especially if you touched or applied rotation > pressure to the gear belt which rotates the > head. It never ca

Zevatech Z Axis fault

Electronics Forum | Tue Jun 23 08:08:38 EDT 2009 | ptxems

We have a couple of Zeva/Juki PM570L's. One machine has developed a fault with the z axis motor. It is continually 'buzzing', we have checked and there is 24VAC on it. Although even on the other machine there is AC voltage on the motor. We have sw

GSM1 occasional fault

Electronics Forum | Thu Feb 04 04:28:52 EST 2010 | mika

You don't by any chance have a s/w called Motion Control s/w? it's on 1-2 floppy diskettes and it will boot from it also. Normally only the UIC field engineers have/has? this. With this we can actually run each axis & valve or whatever independentl

GSM1 occasional fault

Electronics Forum | Thu Feb 04 09:18:18 EST 2010 | mika

Problem! Then replace the motor! Why not replace be belt anyhow? How long was it since the last time you replaced any belt? Another thing you could also do; In the LP (Low Power) chassis lower front left, find the correct motor servo card and "Null

Solder paste jetting vs time pressure dispensing

Electronics Forum | Mon Jun 19 12:42:16 EDT 2023 | daniel_stanphill

The my700 can dispense 1 million dots per hour. It's not an exaggeration either. It literally never stops moving, and is dispensing without contacting the board. It uses the same type of mathematical calculations that a plane dropping a bomb uses in

What pressure is recommended to clean AMT boards after reflow

Electronics Forum | Fri Sep 07 15:19:42 EDT 2001 | davef

Watt tiepoo? [Cereally, you can usually fix typos after you post by using the P yellow �edit� button that shows when you are looking at your posting.] We�re had people on SMTnet that were washing their boards with a brush attached to the end of a ga

De Haart printer expert

Electronics Forum | Thu Feb 12 13:01:12 EST 2004 | patthemack

Thanks for your response. This is a DeHaart MPC-29. It has manual vision, no conveyor. When I bought it, only one camera was working. I fixed that, but while I was jacking with that, the electronic pressure regulator (spcjr) burned up without warning

  1 2 3 4 5 6 7 8 9 10 Next

pressure control/ fault searches for Companies, Equipment, Machines, Suppliers & Information

SMT spare parts - Qinyi Electronics

Reflow Soldering 101 Training Course
Selective soldering solutions with Jade soldering machine

Wave Soldering 101 Training Course
Equipment Auction Automotive Electronics Supplier - Closure of Tier-One SMT Dvision: (10) ASM & Universal SMT Lines & Feeders Equipment as-new-as 2019! Dek | Koh Young | Speedline | Vitronics | Viscom

Best Reflow Oven
Pillarhouse USA for handload Selective Soldering Needs

Training online, at your facility, or at one of our worldwide training centers"
PCB Depanelizers

Low-cost, self-paced, online training on electronics manufacturing fundamentals